GB
- 22 -
5.2 Charging the Li battery pack (Fig. 17-18)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches o
ff
the equipment when the battery is
fl
at.
Warning!
Do not actuate the On/O
ff
switch any
more if the protective circuit has tripped. This may
damage the battery.
1. Remove the battery pack from the handle,
pressing the pushlock button (13) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(12) into the socket outlet. The green LED will
then begin to
fl
ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will
fi
nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that the Li battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the performance of the
equipment drops.
Battery capacity indicator (Fig. 17)
Press the switch for the battery capacity indicator
(Fig. 11/Item A). The battery capacity indicator
(Fig. 11/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED
fl
ashes:
The battery is empty, recharge the battery.
All LEDs
fl
ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6. Operation
6.1 Insert the chain that is to be sharpened
into the chain bar (Fig. 7)
To do this, loosen the chain locking screw (1)
6.2 Set the grinding angle according to the
speci
fi
cations for your chain (Fig. 8) (nor-
mally between 30-35°)
•
Slacken the locking screw for setting the grin-
ding angle (1)
•
Set the desired grinding angle using the scale
(2)
•
Tighten the locking screw (1) again
6.3 Set the chain stopper (Fig. 9/10)
•
Fold the chain stopper (1) onto the chain
•
Pull the chain backwards against the chain
stopper (1) until the latter stops a cutting link
(A). Important! You must make sure that the
angle of the stopped cutting link coincides
with the grinding angle. If it does not, pull the
chain one link further.
•
Fold the grinding head (4) down until the grin-
ding wheel (5) is touching the chain link (A)
that is to be ground. (To do so, you can move
the chain back and forth a little using the set-
ting screw of the chain stopper (2)
6.4 Set the depth limit (Fig. 10)
Fold the grinding head (4) down and set the grin-
ding depth using the setting screw (7)
Important!
The grinding depth should be set
so that the full cutting edge of the cutting link is
sharpened.
6.5 Lock the chain (Fig. 7)
Tighten the chain locking screw (1)
6.6 Grinding the chain links (Fig. 10/11)
Important!
•
Only use the equipment for sharpening saw
chains. Never grind or cut other materials.
•
Before sharpening the saw chain clamp it into
the chain bar. This will prevent jamming of the
grinding wheel caused by a loose saw chain.
•
Slowly guide the grinding wheel to the saw
blade. If the grinding wheel approaches the
Anl_GE_CS_18_Li_Kit_B_SPK7.indb 22
Anl_GE_CS_18_Li_Kit_B_SPK7.indb 22
23.02.2017 08:14:17
23.02.2017 08:14:17
Содержание 44.999.45
Страница 107: ...107 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 107 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 107 23 02 2017 08 14 20 23 02 2017 08 14 20...
Страница 108: ...108 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 108 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 108 23 02 2017 08 14 20 23 02 2017 08 14 20...
Страница 109: ...109 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 109 Anl_GE_CS_18_Li_Kit_B_SPK7 indb 109 23 02 2017 08 14 20 23 02 2017 08 14 20...