EINHELL 44.125.59, Оригинальная инструкция по эксплуатации

Страница: 24 / 122

GB
- 24 -
•
Warning! Adjust the workpiece support (7)
periodically to compensate for wear on the
grinding/sanding wheel (5) / polishing wheel
(6).
5.5 Changing the wheels (Fig. 8-12)
•
Before you replace the wheel: Pull out the po-
wer plug!
•
Undo the three screws (A) in the cover (4)
using a crosstip screwdriver. Pull the screws
(A) out as far as they will go.
•
Lift the cover (4) off.
•
Slacken the recessed head screws (14) as
described in 5.2 so that the spark deflector
(3) can be moved upwards. Position the spark
deflector (3) at the maximum height.
•
If you want to remove the polishing wheel (6),
you also have to remove the cover (4) on the
shaft mount (23) as well. Undo it by placing a
size 17 mm wrench on the nut (B) and ano-
ther wrench, size 12 mm, on the shaft mount
(23) (see Fig. 12).
•
Important! Use a rag, cloth or similar to
prevent the grinding/sanding wheel (5) / poli-
shing wheel (6) from rotating.
•
Undo the nut (B) using a size 17 mm wrench
while holding the grinding/sanding wheel (5)
/ polishing wheel (6) firmly with a rag, cloth or
similar.
•
Important! A size 12 mm wrench and size 17
mm wrench are not supplied with the product.
•
Important! Turn the nut (B) in the direction of
rotation of the grinding/sanding wheel (5) /
polishing wheel (6).
•
Remove the nut (B), flange (C) and old wheel.
•
Carefully clean all parts which rotate during
operation before fitting the new wheel.
•
Fit the new grinding/sanding wheel (5) / poli-
shing wheel (6), flange (C) and nut (B) again
in reverse order and tighten them.
•
Note! Tighten the nut (B) moderately - the
screw connection is designed to promote the
clamping of the grinding/sanding wheel du-
ring operation.
•
Then refit the cover (4) using the 3 screws
(A).
•
Adjust the spark deflector (3) as described
in 5.2.
•
Warning! Check that the safety devices are in
good working condition before you work with
the equipment again.
•
Warning! Always use the grinding/sanding
machine with a grinding/sanding wheel fitted
on each side. This will reduce the risk of tou-
ching a rotating spindle.
5.6 Installing the fl exible shaft (Fig. 13)
•
Insert the flexible shaft (11) with the square
profile in the shaft mount (23) of the tool.
•
Screw the union nut (24) of the flexible shaft
onto the tool by hand (left-hand thread).
Warning!
When you work with the fl exible shaft (11), the
safety glass (2) must be placed right up against
the workpiece support (7) in order to prevent un-
controlled touching of the wheels.
5.7 Inserting the various tools into the fl exib-
le shaft (Fig. 14)
1. Press the supplied locking pin (12) into the
hole in the fl exible shaft (11) and turn the
shaft until the pin latches in place.
2. Then open the clamping sleeve (75) using the
supplied wrench (13).
3. Insert the required tool into the clamping slee-
ve (75) as far as the stop and tighten it using
the wrench (13).
6. Operation
6.1 ON/OFF switch (1)
To switch on the equipment set the On/O ff switch
(1) to position I.
Move the ON/OFF switch (1) to position 0 to
switch o ff the equipment.
Danger!
When you are not working with the fl exible shaft
(11), it is not allowed to be mounted on the
equipment because it could then fl y around out
of control.
After switching on the equipment wait for the
equipment to reach its maximum speed of rotati-
on before commencing with the sanding/grinding
work.
6.2 Speed controller (Fig. 1)
The required speed can be set with the speed
control (10).
6.3 Information on setting the speed for the
fl exible shaft
The correct speed depends on the tool used and
the type of material being processed.
•
Small grinding pins: High speed
•
Large grinding pins: Low speed
Anl_TC-XG_75_Kit_SPK9.indb 24 Anl_TC-XG_75_Kit_SPK9.indb 24 13.07.2020 13:05:44 13.07.2020 13:05:44