![background image](http://html1.mh-extra.com/html/einhell/10-915-31/10-915-31_original-operating-instructions_2370111018.webp)
GB
- 18 -
The outlets must not be used while charging is in
progress.
•
Connect the supplied charger (Fig. 2a) to the
„15 V 1A input“ charging jack (Fig. 1 / Item 8)
on the equipment.
•
Plug the charger into the socket outlet and
the battery will be charged. The LED (Fig. 1/
Item 9) shine (flash) during charging and in-
dicate the charging status. When charging is
finished, all the LEDs shine.
•
The time it takes to fully recharge an empty
battery is approximately 6 hours. The tem-
perature of the battery pack may rise slightly
during the charging operation. This is normal.
5.2 Battery capacity indicator
Press the ON/OFF button (Fig. 1/Item 5) brie
fl
y.
The LED for the battery capacity indicator (Fig. 1
/ Item 9) light up. The number of LEDs that are lit
indicate the current charge level of the integrated
Li-Po battery.
100% charged = 4 LED steady on
>25% charged = 1 LED steady on
<25% charged = no LED steady on
6. LED lamp
Caution! Do not look into the light beam.
•
Press the ON/OFF button for 3 seconds – the
LED lamp (Fig. 1 / Item 1) will be permanently
lit.
•
Press the ON/OFF button again – the LED
lamp will be lit as a „strobe light“.
•
Press the ON/OFF button again – the LED
lamp will be lit as an „SOS“ Morse code sig-
nal lamp.
•
Press the button again to switch the LED
lamp off again.
7. Outputs
Caution!
Check the voltage and current ratings of
the device you want to connect (e.g. mobile pho-
ne, notebook). Observe the operating instructions
for the device.
The supply time varies according to the level of
the charge of the jump start power bank, the level
of power consumption and the intensity of use of
the connected device. The battery needs char-
ging when the remaining charge is 25% (1 LED
shines) (see section 5). The USB ports can be
used in parallel. Please ensure that the cumulati-
ve output current does not exceed 5 A.
7.1 Charging/operating devices with a USB
connection
a) 5V/2A USB outlet
1. Connect an available (or the supplied 2-in-1)
USB connection cable to the USB port (Fig.
1 / Item 2) on the jump start power bank and
then to the device you want to connect (max.
2A).
2. Press the ON/OFF button (Fig. 1 / Item 5).
b) “OUT 5V/9V” USB outlet (Fig. 3)
Note:
If charging does not work with this outlet,
this means that either the device or the cable is
not supported. In this case, use the 5V d.c. / 2A
USB outlet for charging, as described above.
1. Connect the supplied 2-in-1 USB cable (Fig.
2b) to the “OUT 5V/9V” USB port (Fig. 1 / Item
3) on the jump start power bank and then to
the device you want to connect.
2. Press the ON/OFF button (Fig. 1 / Item 5).
3. The parameters required for charging will be
determined at the USB outlet and the connec-
ted device will be charged up. Depending on
the charger cable and the device being char-
ged, the charging time with the “OUT 5V/9V”
USB outlet may be shorter than with the “OUT
5V/2A” USB outlet.
7.2 Operating 19 V d.c. Devices (Fig. 4)
1. Connect the supplied connection cable (Fig.
2d / Item 13) to the 19 V d.c. outlet (Fig. 1 /
Item 7) on the jump start power bank and
then to the 19 V d.c. device, using the sup-
plied connector (Fig. 2d / Item 14) if neces-
sary. The maximum power consumption must
not exceed 3.5A.
2. Press the ON/OFF button (Fig. 1/Item 5).
7.3 Operating 12 V d.c. devices
1. Connect a suitable connection cable to the 12
V d.c. outlet (Fig. 1 / Item 6) on the jump start
power bank and then to the 12 V d.c. device.
The maximum power consumption must not
exceed 10 A.
2. Press the ON/OFF button (Fig. 1/Item 5).
Anl_CE_JS_18_SPK9.indb 18
Anl_CE_JS_18_SPK9.indb 18
22.02.2018 09:33:47
22.02.2018 09:33:47
Содержание 10.915.31
