EIK AM140 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 42

EIK AM140 Скачать руководство пользователя страница 34

www.eikengineering.com

2.8.4 Track roller must be replaced if the value of t is less than 3mm as per figure 2.14 below.

Normally, a track roller and a bushing wear at the same rate and the replacement must
be made simultaneously. Do not let until the rollers are completely wear and the track
link contact with the pontoon body.

Figure 2.14

2.9

Pontoon
Pontoons  provide  sufficient  buoyancy  force  to  float  the  whole  machine  on  open  water.
Sometimes,  the  leaks  may  happen  at  welding  joints  especially  after  the  pontoons  have  been
exposed  to  extreme  environment  for  long  period.  Water  leaks  inspection  must  be  made  for
every 500 hours in order to keep pontoons safe for operation. In other case, inspection must be
made  immediately  if  the  machine  is  tipped  abnormally  to  one  side  during  operating  on  open
water.

2.9.1  Each  pontoon  provides  man  holes  at  the  side  wall  for  maintenance  purpose  (as  per

figure 2.15 on next page).

“Track rollers, pins and bushings life are vary substantially with different travel frequencies and
medium of operation. All these parts are very fast to get wear when the machine is operated at
sandy or muddy area.
“Wearing rate of tracks rollers, pin and bushings does not directly proportional with machine
working hours. A machine that use 2 hours just to travel to work site is facing with faster
wearing rate of track rollers, pins and bushing compare to a machine that use 2 hours to load or
unload earth from a lorry in static condition”.
“All shown maintenance frequencies for track rollers, pins and bushings are for suggestion and
reference only and actual practice could be different”.

31

«
...
32
33
34
35
36
...
»

Содержание AM140











































Отзывы:

Нет отзывов