background image

 

1

-800-497-4524                   EIC SOLUTIONS, INC

.

                       215-443-5190 

1.  GENERAL INFORMATION 

1.1 PRINCIPLES OF OPERATION 

n 1834 Jean Peltier discovered that by passing a current through two dissimilar conductors the 
junction of those materials will either absorb or release heat depending on the direction of the 

current flow.   Thirteen years earlier, Thomas Seebeck had discovered that current would flow 
when you placed a temperature gradient across the junction of two dissimilar metals.  These 

two discoveries were the basis of thermoelectrics.  With the advent of modern semiconductors, 

thermoelectric devices became practical for real world applications and are now found in 
everything from consumer goods to spacecraft.   

Your EIC Solutions Thermoelectric Air Conditioner operates on this same principle so there 

is no compressor and no expensive, ozone depleting CFC’s.  EIC’s air conditioners use 
Thermoelectric “modules” sandwiched between high performance aluminum heat sinks, high CFM 
axial fans, and a patented electronic design to “pump” the heat from the inside of your enclosure 
to the outside, without exposing your delicate electronics to any outside air or contaminates.  See 
Figure 1.1.  

EIC uses only the highest quality components in our air conditioners and you can expect 

years of trouble free cooling from these solid-state devices.  Every unit we sell is backed by our 
one year parts and labor warranty. 

 

FIGURE 1.1 

AMBIENT AIR 

REMOVES HEAT 

FROM HOT SIDE 

HEAT SINK

COLD AIR 

CIRCULATED 

WITHIN THE 

ENCLOSURE

HOT

SIDE

HEAT 

SINK

COLD 

SIDE 

HEAT 

SINK

FAN

FAN

I

Содержание AAC-120-4XT Series












Отзывы: