Ei Electronics RadioLINK Ei262 Скачать руководство пользователя страница 34

Страница: 34 / 40

Repeater Function

: To disable the Repeater function press and hold the test button until the

alarm sounds and the

RadioLINK

red light turns on. Immediately (while the

RadioLINK

light is still on), press and hold the house code switch with a

small screwdriver, until the red indicator light gives 3 slow flashes.
Immediately release the switch and test button.

To re-activate the Repeater function just follow the instructions above for
disabling. The indicators light will flash 15 or 16 times and stop to show the
Repeater function is now activated.

Dimensions

: 126 x 150 x 42 mm.

Weight: 330g.

13. ACCESSORIES

RadioLINK Remote System Control Ei411H3

(for use with models Ei161RC/164RC/166RC/Ei2110 Alarm on an Ei168RC Base & Ei262 CO Alarm only)

The

RadioLINK

System Control Switch is recommended for systems with at least one Carbon Monoxide

Alarm and three or more Smoke / Heat / Fire Alarms. It allows the user to perform the following functions
from a remote location:

LOCATE - If alarms sound press

Locate

to allow source of alarm to be identified (audibly).

HUSH - Press

Hush

to silence nuisance alarms.

TEST - Operate weekly to

Test

the alarms.

RadioLINK Relay Module Ei428

This module is a device that switches an internal relay upon receipt of an alarm signal from a

RadioLINK

device – useful for turning off gas valves, signalling to panels, turning on strobes etc. It is mains powered
with battery back-up.

B16587-R0-262-UC-ENG 15/4/09 3:38 PM Page 34

Содержание RadioLINK Ei262









































Результаты поиска

Содержание RadioLINK Ei262

Отзывы:

Бренды по названию

Популярные бренды

Ei Electronics RadioLINK Ei262, Инструкция пользователя

Результаты поиска

Содержание RadioLINK Ei262

Отзывы:

Бренды по названию

Популярные бренды