manualshive.com logo in svg

Ei Electronics EIB140RC Series, Инструкция по эксплуатации, Страница: 14 / 16

Поделиться
Скачать
Ei Electronics EIB140RC Series Скачать руководство пользователя страница 14

WARNING:

 Mains operated Alarms should be installed 

and interconnected by a licensed electrician in 

accordance with the Australian wiring rules AS3000. 

Failure to install this Alarm correctly may expose the 

user to shock or fire hazards.

WARNING:

 The Alarm must be continuously powered 

24 hours a day so it is important that it is not on a circuit 

that can be turned off by a switch.

Note:

 The EIB168RC RadioLINK Base can be used to eliminate 

interconnect wiring, make system extensions and provide a 

simple and cost effective solution.

Mounting & Wiring Alarms

1.

 Select a location complying with the advice in the 

(Positioning Alarms section).

2.

 Disconnect the AC mains supply from the circuit that 

is going to be used.

3.

 Lift off the wiring cover as shown in 

Figure 3

.

The house wiring must be connected to the terminal block 

on the mounting plate as follows:

L: Live

 - connect to the house wires coloured brown or 

marked L.

N: Neutral

 - connect to the house wires coloured blue 

or marked N.

See page 16 for information on interconnection.

Note: Wiring must be installed in compliance with 

AS3000

Warning:

 Mixing the Live and Neutral connections 

when interconnecting alarms will damage all the 

alarms - ensure that the same colours are used 

throughout the premises for Live, Neutral and 

Interconnect wires.

We strongly recommend that you check for the following 

before connecting the Alarm

:

• check for Live and Neutral using a two probe tester. 

• check for Live using a neon tester. 

• check that the Interconnect wire is NOT connected to 

Live, Neutral or Earth. 

Do not use an Earth wire for 

the Interconnect line.

N.B. The Alarm does not need to be earthed. However the 

terminal marked        is provided for the convenience of the 

installer so that any copper Earth wire or cable coloured 

green & yellow, can be safely terminated.
To interconnect the Alarms connect all the IC terminals 

together as shown in 

Figure 4

 (see “

Interconnecting 

Alarms

” section on page 16).

14

FOAM CEILING GASKET

INSERT SCREWDRIVER

TO LIFT AND REMOVE

WIRING COVER

Figure 3

Содержание EIB140RC Series

















Отзывы:

Нет отзывов