background image

5

5.2 Installation away from the Alarm
WARNING
: When the relay is not installed underneath an Alarm,  

the cover supplied must be fitted to ensure the user is not exposed 

to fire or shock hazards.

1. Install the Alarm(s) as described in their manuals.

2. Install the Relay Base near the auxiliary device or in some 

other location convenient for wiring. Where the incoming wiring is 

surface mounted, the appropriately sized ducting/conduit must be 

chosen to mate with the unit.  Use a sharp knife to remove material 

from the selected knockout, making sure that there is no gap when 

mated with ducting / conduit. There are three knockouts – two 

on the sidewall and one on the rear. DO NOT USE the knockout 

closest to the P/C switch.

3. Remove the required knockout, bringing the wiring from one 

of the Alarms through it and connecting the three wires (L=Live, 

N=Neutral and IC=Interconnect) to the Relay Base mains terminal 

block. (Screw tightening torque: max 0.5Nm (5.1kgf.cm)).

4. Screw the Relay Base in place. 

5.3 Wiring the relay

1.  Connect the L (Live) wire from the power supply of the auxiliary 

device to the C (Common) terminal.

2. Then connect either the NC or NO contact of the relay 

(depending on what is required for controlling the auxiliary 

device) to the auxiliary device. For example, if the relay is used 

to cut out a boiler in case of alarm, then NC should be used but 

for a Beacon that should only be on in case of alarm, then the 

NO should be used.

Ei128R / Ei128RBU

The above shows the connection for Carbon Monoxide Alarms.

Connect the Smoke/Heat Alarm similarly but on a separate circuit to the

Carbon Monoxide Alarm (unless an Ei1529RC Control Switch is used on the system)

Ei3018

Ei3018

Figure 5

L

IC

N

Earth wire if 

present

C

NC

NO

L

IC

N

Auxiliary 

Device

Mains Alarm

Ei128R / Ei128RBU

Auxiliary Device

Power Supply

Alarm and Relay

Power Supply

(230V AC)

+

-

L

IC

N

Earth wire if 

present

C

NC

NO

L

IC

N

C

NC

NO

External Device

(230V AC)

Mains Alarm

+

-

C

NC

NO

Alarm and Relay

Power Supply

(230V AC)

Ei128R / Ei128RBU

Figure 6

Содержание Ei128R









Отзывы: