Ego Power+ ST1400E-ST, Руководство оператора

Страница: 9 / 228

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1400E-ST
9
EN
NOTICE:
Line release will require multiple tapping as the
cutting line becomes shorter.
WARNING:
Do not remove or alter the line cutting
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
LINE REPLACEMENT
NOTICE:
Always use the recommended nylon cutting line
with a diameter that does not exceed 2.4 mm. Using line
other than that specified may cause the line trimmer to
overheat or become damaged.
WARNING:
Never use metal-reinforced line, wire,
or rope, etc. These can break off and become dangerous
projectiles.
1. Remove the battery pack.
2. Remove the remaining cutting line, if necessary.
3. Cut 4 m of cutting line. Insert the line into the
mounting hole inside the eyelet (Fig. O). Push and pull
the line from the other side until equal amounts of
line appear on both sides of the spool.
4. Install the battery pack onto the string trimmer.
5. Press and hold the line-loading button to start the
line-winding motor. The line will be wound into the
trimmer head continuously (Fig. P).
6. Watch the remaining line length carefully. Briefly
press the line loading button to adjust the length until
13 cm of the line is showing on each side.
7. Push down on the trimmer head while pulling on the
lines to manually advance the line in order to check
for proper assembly of the cutting line.
When the cutting line breaks from the line outlet or the
cutting line is not released when the trimmer head is
tapped, follow the steps below
1. Remove the battery pack from the trimmer.
2. Press the release tabs on the trimmer head and
remove the lower cover assembly by pulling it
straight out (Fig. Q).
3. Remove the cutting line from the spool.
4. Insert the spring into the slot in the lower cover
assembly (Fig. R).
5. With one hand holding the trimmer, use another hand
to grasp the lower cover assembly and align the
slots in the lower cover assembly with the release
tabs. Press the lower cover assembly until it snaps
into place, at which time you will hear a distinct click
sound (Fig. S).
6. Follow the instructions in the “
LINE REPLACEMENT
”
section to reload the cutting line.
TRIMMER HEAD REPLACEMENT
WARNING:
If the head loosens after it is fixed in
position, replace it immediately. Never use a trimmer with
a loose cutting attachment. Replace a cracked, damaged
or worn out cutting head immediately, even if damage
is limited to superficial cracks. Such attachments may
shatter at high speed and cause serious injury.
REMOVE THE TRIMMER HEAD
1. Remove the battery pack from the trimmer.
2. Press the release tabs on the trimmer head and
remove the lower cover assembly of the trimmer
head by pulling it straight out.
3. Remove the cutting line from the trimmer head
(Fig. S).
4. Take the spring out of the spool assembly, if
necessary. Save it for reassembly.
5. Wear gloves. Use one hand to grasp the spool
assembly to stabilize it, and use the other hand to
hold an impact wrench
( not included ) to loosen the
nut in a counterclockwise direction (Fig. X).
6. Remove the nut, spool retainer, upper cover, upper
base cover, from the motor shaft (Fig. T).
NOTICE:
Two bushings easily fall off the motor shaft,
pleas save them carefully for reassembly.
7. Replace with a new trimmer head and mount it in
following steps.
T-1 Bushing T-6 Trimmer Line
T-2 Upper Cover T-7 Lower Cover
T-3 Nut T-8 Upper base cover
T-4 Washer T-9 Assembly Spool Assembly
T-5 Spring
INSTALL THE NEW TRIMMER HEAD
1. Mount the bushings in motor shaft and mount the
upper base cover assembly into place (Fig. T).
2. Mount the upper cover, spool assembly, washer and
nut in that order. Use an impact wrench on the nut to
tighten it (Fig. U & V).
3. Mount the lower cover assembly.
4. Reload the cutting line.
5. Start the tool to see whether the string trimmer will
work normally. If it does not, reassemble as described
above.