Efco DS 2200 S Скачать руководство пользователя страница 7

Страница: 7 / 52

BRUSCHCUTTERS DS 2200 - DS 2400

pag.

Workshop manual

2. SAFETY

Recognize Safety Information

This is the safety-alert symbol. When you see this

symbol on your machine or in this manual, be

alert to the potential for personal injury. Follow

recommended precautions and safe servicing

practices.

Understand Signal Words

A signal word - DANGER, WARNING, or CAUTION

- is used with the safety-alert symbol. DANGER

identifies the most serious hazards.

DANGER or WARNING safety signs are located

near specific hazards. General precautions

are listed on CAUTION safety signs. CAUTION

also calls attention to safety messages in this

manual.

Handle Fluids Safely - Avoid Fires

Be Prepared For Emergencies

When you work around fuel, do not smoke or

work near heaters or other fire hazards.

Store flammable fluids away from fire hazards.

Do not incinerate or puncture pressurized

•

containers.

Make sure machine is clean of trash, grease,

and debris.

Do not store oily rags; they can ignite and burn

spontaneously.

Be prepared if a fire starts.

Keep a first aid kit and fire extinguisher

handy.

Keep emergency numbers for doctors, ambulance

service, hospital, and fire department near your

telephone.

Wear Protective Clothing

Wear close fitting clothing and safety equipment

appropriate to the job.

•

Содержание DS 2200 S





















































Результаты поиска

Содержание DS 2200 S

Отзывы:

Похожие инструкции для DS 2200 S

Бренды по названию

Популярные бренды

Efco DS 2200 S, Руководство по ремонту

Результаты поиска

Содержание DS 2200 S

Отзывы:

Похожие инструкции для DS 2200 S

Бренды по названию

Популярные бренды