manualshive.com logo in svg
background image

13

13

16

15

KRAFTSTOFFGEMISCH (Abb. 9-10)
Verwenden Sie ein 4%ges (25:1) Kraftstoffgemisch (Öl/Benzin).
Mit Öl PROSINT Efco verwenden Sie ein 2%ges (50:1) Gemisch.

ACHTUNG! – 2-Takt-Motoren haben eine hohe spezifische
Leistung, so dass Sie verbleitem oder unverblaitem Benzin

bekannter Marken mit einer Oktanzahl von mindestens 90
verwenden sollten. ÖRTLICHE VORSCHRIFTEN REGELN DIE ZU
VERWENDENDE BENZINART (VERBLEIT ODER BLEIFREI)
DIESE VORSCHRIFTEN SIND STRIKT EINZUHALTEN!
- Bewahren Sie das Benzin, Öl und Gemisch in genormten Behältern

auf (Abb. 11).

- Verwenden Sie zur Aufbereitung des Gemischs ausschließlich Öl

für 2-Takt-Motoren (Abb. 12).

- Schütteln Sie den Gemischkanister vor dem Auftanken (Abb. 13).
- Tanken Sie stets bei abgestelltem Motor und von Flammen entfernt

(Abb. 14).

- Damit beim Aufdrehen des Tankverschlusses kein Kraftstoffgemisch

verschüttet wird, stellen Sie der Kettensäge auf eine ebene und
standfeste Fläche ab. Öffnen Sie den Verschluss äußerst vorsichtig,
um den Tankdruck langsam entweichen zu lassen und
ausspritzenden Kraftstoff zu vermeiden.

- Mischen Sie jeweils nur die erforderliche Kraftstoffmenge an. Das

fertige Kraftstoffgemisch darf nur kurze Zeit im Tank bzw. Kanister
bleiben. Mit Beigabe des Zusatzstoffs ADDITIX 2000 (Abb. 15) von
Emak Bestellnummer 001000972 können Sie das Gemisch für den
Zeitraum eines Jahres aufbewahren.

ACHTUNG

– Das Einatmen der Abgase ist

gesundheitsschädlich.

SCHMIERUNG DER KETTE
Die Verwendung des richtigen Schmiermittels während des Schnittes
reduziert den Verschleiß von Schwert und Kette auf ein Minimum und
gewährleistet so eine höhere Lebensdauer. Verwenden Sie stets qua-
litativ hochwertiges Öl (Abb. 16).

ACHTUNG - Verwenden Sie auf keinen Fall Altöl! Verwen-
den Sie immer biologisch abbaubares Spezialschmiermittel
für Stangen und Ketten (eco-lube Efco cod. 1108014), um
die Umwelt zu schonen und eine lange Lebensdauer der
Bauteile der Motorsäge zu gewährleisten.

MEZCLA COMBUSTIBLE (Fig. 9-10)
Use combustible (mezcla aceite/gasolina) al 4% (25:1).
Con aceite PROSINT Efco utilice mezcla al 2% (50:1).

¡ATENCIÓN!  Los motores de dos tiempos tienen una po-
tencia específica elevada, por lo cual se aconseja el uso de

gasolina con o sin plomo de marca conocida, con un número
de octanos no inferior a 90
.  LAS LEYES LOCALES REGLA-
MENTAN EL TIPO DE GASOLINA QUE DEBE UTILIZARSE
(CON O SIN PLOMO). ES OBLIGATORIO RESPETARLAS.
- Conserve la gasolina, el aceite y la mezcla en recipientes homo-

logados (Fig. 11).

- En la preparación de la mezcla, utilice sólo aceite específico

para motores de dos tiempos (Fig. 12).

- Agite el bidón de la mezcla antes de verterla (Fig. 13).
- Cargue siempre el combustible (Fig. 14) con el motor apagado y

lejos de cualquier llama.

- Antes de desenroscar el tapón del depósito, apoye la motosierra

en una superficie llana y firme de modo que no se tumbe. Abra
con cuidado el tapón para aliviar lentamente el exceso de pre-
sión y evitar que el combustible salpique.

- Prepare sólo la mezcla necesaria para el uso; no la deje en el

depósito o en el bidón durante mucho tiempo. Se aconseja utili-
zar aditivo ADDITIX 2000 (Fig. 15) de Emak, cód. 001000972,
para conservar la mezcla durante un año.

ATENCIÓN – Inhalar los gases de escape es nocivo para la
salud.

ACEITE LUBRICANTE PARA CADENA
La correcta lubricación de la cadena durante las distintas fases de
corte reduce al mínimo el desgaste entre la cadena y la barra ase-
gurando, por lo tanto, su mayor duración. Utilice siempre aceite de
buena calidad (Fig. 16).

ATENCION - Está prohibido usar aceite recuperado. Uti-
lizar siempre un lubricante biodegradable específico
(eco-lube Efco cod. 1108014) para barras y cadenas que
tenga en cuenta el tipo y la vida útil de los componen-
tes de la motosierra.

BRANDSTOFMENGSEL (Fig. 9-10)
Gebruik brandstof (mengsel olie/benzine) van 4% (25:1).
Gebruik met olie PROSINT Efco een mengsel van 2% (50:1).

LET OP! – De tweetaktmotoren hebben een hoog specifiek
vermogen, wij adviseren derhalve het gebruik van met lood of

loodvrije benzine  van een bekend merk, met een octaangehalte
van minstens 90. HET TYPE BENZINE DAT GEBRUIKT MOET
WORDEN (LOODHOUDEND OF LOODVRIJ) IS BIJ DE WET GE-
REGELD. NEEM DEZE VOORSCHRIFTEN IN ACHT!
- Bewaar de benzine, de olie en het mengsel in goedgekeurde contai-

ners (Fig. 11).

- Gebruik bij de bereiding van het mengsel uitsluitend olie die speci-

fiek bedoeld is voor tweetaktmotoren (Fig. 12).

- Schud de jerrycan met het mengsel alvorens de tank te vullen (Fig.

13).

- Vul de brandstoftank (Fig. 14) altijd met uitgeschakelde motor en uit

de buurt van vlammen.

- Leg de motorzaag op een vlakke, stevige ondergrond alvorens de

dop van de tank los te schroeven, zodat het apparaat niet kan om-
vallen. Maak de dop voorzichtig open om de hoge druk langzaam af
te voeren en om te vermijden dat de brandstof naar buiten spat.

- Bereid alleen de hoeveelheid mengsel voor die nodig is voor het ge-

bruik; laat het niet lange tijd in de tank of de jerrycan zitten. Het wordt
geadviseerd de toevoeging ADDITIX 2000 (Fig. 15) van Emak art.
nr. 001000972 te gebruiken, om het mengsel een jaar lang te kun-
nen bewaren.

LET OP – Het inademen van het uitlaatgas is schadelijk voor de
gezondheid.

KETTINGSMEEROLIE
Een goede smering van de ketting gedurende het gebruik vermindert
de slijtage tussen de ketting en het zaagblad tot een minimum en ver-
zekert een langere levensduur. Altijd een goede kwaliteitsolie ge-
bruiken (Fig. 16).

LET OP - Er mag geen oude olie hergebruikt worden! Ge-
bruik altijd een biologisch afbreekbaar smeermiddel (eco-
lube Efco cod. 1108014), speciaal bedoeld voor zaagbla-
den en kettingen, om het milieu en de onderdelen van de
motorzaag zoveel mogelijk te sparen.

Deutsch

Español

Nederlands

ANLASSEN

STARTEN

PUESTA EN MARCHA

14

Содержание 136

































Отзывы: