background image

   

 
 

 

Eemax, Inc.™ Electric Tankless Water 

Heaters 

 

INSTALLATION INSTRUCTIONS & OWNER’S MANUAL 

 

 

HotMax™

  

HM013240 

 

IMPORTANT SAFETY INFORMATION 

When installing or using any high voltage electrical appliance, basic safety precautions should always be 
followed. Under no circumstance should you attempt to clean, install, inspect, repair, disassemble or 
otherwise service this water heater, without first shutting off 

all

 power to the unit directly at the circuit 

breaker box. 

SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING. 

THIS PRODUCT SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN AND A QUALIFIED PLUMBER IN 
ACCORDANCE WITH ALL NATIONAL, STATE, PROVINCIAL AND LOCAL ELECTRICAL & PLUMBING CODES. 

PLEASE READ THESE INSTRUCTIONS THOROUGHLY AND COMPLETELY PRIOR TO INSTALLATION & USE. 
FAILURE TO DO SO COULD CAUSE PROPERTY DAMAGE, SERIOUS INJURY, OR DEATH.  

 

This manual should be given to the owner after installation and should be retained for future reference. 

 

 

Tested and certified by the Water Quality Association against NSF/ANSI 372 for lead free 
compliance. 

 

 

Recognize this symbol as an indication of Important Safety Information! 

 

DO NOT 

destroy this manual. Please read carefully and keep it in a safe place for future reference 

 

 

 

 

Содержание HotMAx HM013240

















Отзывы: