EemaX AUTOBOOSTER Скачать руководство пользователя страница 5

Страница: 5 / 20

3- SETTING UP TO INSTALL

Recommended Clearances:

14 inches from above the existing tank heater to the next obstruction
6 inches in front of and to the sides of the AutoBooster™, for service maintenance

14 inches

Pre-Mounting Steps

1. SHUT OFF ELECTRICITY ON YOUR CIRCUIT BREAKER BEFORE PROCEEDING TO ANY FURTHER

INSTALLATION STEPS.

2. Make sure there is at least 14 inches of straight pipe clearance above the tank heater. This is the

required room in order for the unit to effectively connect in series with the tank and outlet pipe.

3. Close the supply water valve to the tank heater. In most cases, this is located above the tank heater

on the cold water inlet side. You must do this to drain your system.

4. Open the drain valve of the water tank to let the tank completely deplete of water. The drain valve

is usually located near the bottom of the tank.

5. Drain the water from all existing hot water pipes by first opening all hot water faucets of any kind

in the house. Leave the faucets open until plumbing installation is complete. If water does not stop

flowing, check to make sure the inlet water to the tank heater has been completely shut off.

6. Assess your plumbing system before you cut the pipe – possible plumbing layouts on the following

page.

CUTTING THE PIPE IS A CRITICAL STEP. IT IS IMPERATIVE YOU REFER TO THE GUIDE ON THE

FOLLOWING PAGES FOR CLEAR INSTRUCTIONS ON HOW TO CUT THE HOT COPPER PIPE.

Downloaded from https://gadgetsgo.com/AutoBooster-HATB007240-water-tank-heater-boost.html Authorized Eemax Dealer

Содержание AUTOBOOSTER





















Результаты поиска

Содержание AUTOBOOSTER

Отзывы:

Похожие инструкции для AUTOBOOSTER

Бренды по названию

Популярные бренды

EemaX AUTOBOOSTER, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание AUTOBOOSTER

Отзывы:

Похожие инструкции для AUTOBOOSTER

Бренды по названию

Популярные бренды