EemaX AUTOBOOSTER Скачать руководство пользователя страница 17

Страница: 17 / 20

9- USER INTERFACE

AutoBooster™ Features

List of Menu Options Provided by the Software (Clarified Below and on Following Page):



Inlet/Outlet Temperature Reading



Active Unit in Operation



Activation Temperature



Max Temperature



Software Version



Eco Mode



Vacation Mode



Freeze Protect

Primary Menu Cycle Screens

Turn the control knob in either direction to cycle through menu options.

Inlet/Outlet Temperature Reading

The temperature of the water going in and out of the AutoBooster™ can be

observed from this display.

Active Unit in Operation

This screen will tell the user which heating unit is operating at that given

point in time. It will either be the pre-existing water tank (“TANK”) or the

AutoBooster™ (“UNIT”).

Flow

The flow screen will tell the user the amount of water that is flowing

through the unit in gallons per minute.

Load Factor

Here you can see how hard your AutoBooster™ is working.

Clock

Set the time here (HOURS:MINUTES:SECONDS). Press the knob to cycle

through hours, minutes, seconds and turn the knob to adjust the number.

IN 71 F
OUT 69 F

TANK OFF
UNIT ON

FLOW
0.00 GPM

PWM

88%

CLOCK
01:23:57

Downloaded from https://gadgetsgo.com/AutoBooster-HATB007240-water-tank-heater-boost.html Authorized Eemax Dealer

Содержание AUTOBOOSTER





















Результаты поиска

Содержание AUTOBOOSTER

Отзывы:

Похожие инструкции для AUTOBOOSTER

Бренды по названию

Популярные бренды

EemaX AUTOBOOSTER, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание AUTOBOOSTER

Отзывы:

Похожие инструкции для AUTOBOOSTER

Бренды по названию

Популярные бренды