manualshive.com logo in svg

Edwards XDS100B, Инструкция по эксплуатации

Поделиться
Скачать
Edwards XDS100B Скачать руководство пользователя страница 34

A732-01-880 Issue A

Page 28

© Edwards Limited 2010. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Service, spares and accessories

7.3.4

Solenoid operated pipeline valves

Fit the pipeline valve between your vacuum system and the pump inlet to provide additional system protection when 
the pump is switched off. The following valves are available as accessories and are recommended. (Refer to 

Table 11

).

7.3.5

Tip seal and exhaust valve service kit

This kit contains all the necessary components to replace the tip seals. Tip seals should be replaced as a pair, and 
only simple tools are required. The kit part number is A732-01-801.

--

Table 11 - Solenoid operated pipeline valves

Product description

Ordering information

PV40EK Valve, 220-240 V 50/60 Hz, Aluminium

C414-01-000

PV40EK Valve, 220-240 V 50/60 Hz, Steel

C414-02-000

PV40EK Valve, 110-127 V 50/60 Hz, Aluminium

C414-03-000

PV40EK Valve, 110-127 V 50/60 Hz, Steel

C414-04-000

Содержание XDS100B



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды