Edwards XDS100B Скачать руководство пользователя страница 11

Страница: 11 / 34

Page 5

Edwards and the Edwards logo are trademarks of Edwards Limited.

Technical data

A732-01-880 Issue A

Technical data

2.1

Operating and storage conditions

2.2

Performance

2.2.1

General

Note:

If the pump is operated outside the specified limits, then the inverter may reduce the motor speed; tip seal
wear rate will be increased.

Table 1 - Operating and storage conditions

Operating and storage conditions

XDS100B

Ambient temperature range (operation)

+10 °C to +40 °C

Maximum surface temperature of pump body under normal operating conditions
and maximum ambient temperature

+40 °C to +70 °C

Maximum humidity (operation)

90% RH

Ambient temperature range (storage)

–30 °C to +70 °C

Table 2 - CSA approval environmental conditions

Parameter

XDS100B

Pollution

Pollution degree 2

Installation

Installation category II

Altitude restriction

Max 2000 m

Area of use

Indoor use

Table 3 - General characteristics

General

XDS100B

Nominal peak pumping speed

95 m

XDS100B used in combination with XDS35i backing pump.

Maximum permitted continuous inlet pressure

20 mbar

Maximum permitted continuous exhaust pressure

60 mbar

Maximum permitted inlet pressure for short duration

1.5 bar(a)

Maximum chamber volume to pump down from atmospheric pressure

100 litres

Maximum chamber volume for cyclic duty - maximum 6 cycles per hour

50 litres

Suckback protection

Provided by backing pump

Leak tightness

<1x10

-6

mbar l s

-1

Содержание XDS100B





























Результаты поиска

Содержание XDS100B

Отзывы:

Бренды по названию

Популярные бренды

Edwards XDS100B, Инструкция по эксплуатации

Результаты поиска

Содержание XDS100B

Отзывы:

Бренды по названию

Популярные бренды