Edwards nXR120i Скачать руководство пользователя страница 19

Страница: 19 / 56

4. Installation

4.1 Installation safety

CAUTION: SAFETY INSTRUCTIONS

Follow all safety instructions and take note of all appropriate precautions.

Possible hazards on the dry pumping system include electricity, process chemicals, and

Fomblin® (PFPE) oil:

▪

Refer to the safety manual P40040100 for safety information for the specification,

design, operation and maintenance of vacuum pumps and vacuum systems.

▪

on installation.

▪

Do not remove the temporary covers from the system inlet and exhaust until ready

to connect.

▪

Do not operate the system unless the inlet and exhaust are connected to the

vacuum and exhaust extraction system.

▪

Isolate the other components in the process system from the electrical supply to

prevent accidental operation.

▪

Electrical supplies are potentially hazardous energy sources. Lockout and tagout

before you do the maintenance.

▪

Obey all national and local rules and safety regulations when you install the

system.

▪

Tighten the cables, hoses and pipework during installation to prevent a trip hazard.

▪

Make sure that the installation area is clean and free from debris and

contamination before you install the pump.

▪

Make sure that all facilities given in this manual are available for the system to

perform correctly.

WARNING: BLOCKED EXHAUST PIPELINE

Risk of damage to equipment. Make sure the exhaust pipeline is not blocked. If an

exhaust isolation valve is used, make sure that the pump is not operated with the

valve closed.

4.2 Unpack and inspect

WARNING: DAMAGED PUMP

Risk of injury to people or damage to equipment. Do not use the pump if it is

damaged. Failure to do so can result in injury to people and/or damage to

equipment.

05/2021 - ©Edwards Limited

Page 19

A90301880_C

A90301880_C - Installation

Содержание nXR120i

























































Результаты поиска

Содержание nXR120i

Отзывы:

Похожие инструкции для nXR120i

Бренды по названию

Популярные бренды

Edwards nXR120i, Инструкция по эксплуатации

Результаты поиска

Содержание nXR120i

Отзывы:

Похожие инструкции для nXR120i

Бренды по названию

Популярные бренды