Edwards nXDS10i nXDS15i Скачать руководство пользователя | Manualshive

Страница: 47 / 58

background image

Figure 14 Noisy pump flow chart

7.5 The pump surface temperature is high

▪

The ambient temperature is too high.

▪

The cooling fan is not running.

▪

The process gas is too hot or the maximum continuous operating pressure has

been exceeded.

7.6 Alarm indicator codes

Whenever a fail condition becomes active the red alarm indicator shows a flashing

sequence. If the error light is on continuously this indicates a problem has been found

with the embedded software. In this case, try cycling the power. If cycling the power

does not clear the indication, a software download may be required. In this situation,

contact us or the supplier. If the alarm indicator is flashing, identify the error flash code

Table: Flashing error codes on page 46

There is a sufficient off period between each subsequent cycle repetition to clearly mark

the start of a new flash sequence. The duration of a long flash (L) is equal to 3 times the

duration of a short flash (0.5 s).

Page 45

A73501880_G - Fault finding

«
...
45
46
47
48
49
...
»

Содержание nXDS10i nXDS15i



























































Отзывы:

Нет отзывов

Похожие инструкции для nXDS10i nXDS15i

Бренд: Nelson Страницы: 12

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: Zodiac Страницы: 23

Бренд: SAER Elettropompe Страницы: 36

Бренд: Wayne Страницы: 8

Бренд: Graco Страницы: 48

Бренд: Flotec Страницы: 24

Бренд: Mannesmann Страницы: 3

Бренд: Rinnai Страницы: 67

Бренд: A.O. Smith Страницы: 44

Бренд: Oase Страницы: 7

Бренд: DAYLIFF Страницы: 12

Бренд: AMICOCIRC Страницы: 13

Бренд: Becker Страницы: 4

BASEMENT SENTRY STBC201Q

Бренд: Zoeller Страницы: 22

Бренд: Red Jacket Страницы: 42

Бренд: AquaScape Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды