Edwards iXL1000 Скачать руководство пользователя страница 66

Страница: 66 / 70

A540-55-880 Issue D

Page 58

Edwards and the Edwards logo are trademarks of Edwards Limited.

Appendix A2

Alarm 62.12
MB E/C Temp High

See manual

The booster end cover
temperature has reached the
maximum allowed so the booster
has stopped.

Refer to

Section 4.5

to determine

the temperature that triggered
the alarm.
See Warning 62.11 for causes and
actions.

Alarm 174.10
Booster Stopped

See manual

Booster speed too low - rotor is
probably locked.

Contact Edwards

Alarm 176.01
MB INV xxxx yyyy

xxxx yyyy
aaaaaaaaaaaaaaaa

Booster Inverter has raised an
alarm and stopped the system.

Refer to

A2.3

for more

information.

Alarm 176.01
MB Not Running

See manual

Booster Inverter will not start up
when requested.

Check inverter fault history.

Alarm 176.13
No MB Inv Comms

See manual

The pump controller cannot
communicate with the booster
inverter during start-up checks.

Check the wiring between the
pump controller and the booster
inverter.

Alarm 184.10
Dry Pump Stopped

See manual

The dry pump speed is very low.
The rotor might be locked.

Cycle the power to the pump and
attempt to re-start. If this fails,
contact Edwards.

Alarm 186.01
DP INV xxxx yyyy

xxxx yyyy
aaaaaaaaaaaaaaaa

Dry Pump Inverter has raised an
alarm and stopped the system.

Refer to

A2.3

for more

information.

Alarm 186.01
DP Not Running

See manual

Dry Pump Inverter will not start up
when requested.

Check inverter fault history.

Alarm 186.13
No DP Inv Comms

See manual

The pump controller cannot
communicate with the dry pump
inverter during startup checks

Check the wiring between the
pump controller and the dry pump
inverter

Table A14 - Alarms (continued)

Warning Message
on PDT

'Action' Message on
PDT

Possible Cause

Action

Содержание iXL1000


































































Результаты поиска

Содержание iXL1000

Отзывы:

Похожие инструкции для iXL1000

Бренды по названию

Популярные бренды

Edwards iXL1000, Инструкция по эксплуатации

Результаты поиска

Содержание iXL1000

Отзывы:

Похожие инструкции для iXL1000

Бренды по названию

Популярные бренды