© 2018 United Technologies Corporation
1 / 4
P/N 3102000-
EN • REV 002 • ISS 16MAR18
Genesis WG4 Outdoor Horn-
Strobe Installation Sheet
Description
The Genesis WG4 Outdoor Horn-
Strobe
is a life safety notification
appliance designed for indoor or outdoor use on ceilings or on walls.
See Table
1 for a list of models and
Table
2 for a list of accessories.
For surface mount applications, mount the WG4 onto a Model 449
electrical box using the gasket shipped with the a
ppliance. For flush
mount applications where the mounting surface is flush with the
surface of the wall or ceiling, use the WG4GSKT gasket kit.
Note that you need a Model 449 electrical box for waterproof
applications, or a standard mount 4
in. square box
for all other
applications.
The horn-
strobe
includes field-
configurable jumper options that allow
you to set the strobe pattern to temporal or continuous, the horn
pattern to temporal or continuous, and the horn volume to low or high.
The horn-
strobe
also includes a field-
configurable switch for setting the
strobe candela level. This setting is locked in place and is visible after
final installation.
Table 1: Models
Number
Description
WG4WF-
HVMC
Outdoor rated wall/ceiling horn-
strobe
, white with
FIRE marking, clear lens
WG4WN-
HVMC
Outdoor rated wall/ceiling horn-
strobe
, white
without marking, clear lens
WG4RF
-
HVMC
Outdoor rated wall/ceiling horn-
strobe
, red with
FIRE marking, clear lens
WG4RN
-
HVMC
Outdoor rated wall/ceiling horn-
strobe
, red
without marking, clear lens
Table 2: Accessories
Number
Description
WG4WTS [1]
Outdoor-
rated surface skirt, white, for Genesis WG4
horn or horn-
strobe
WG4RTS [1]
Outdoor-
rated surface skirt, red, for Genesis WG4
horn or horn-
strobe
WG4GSKT [2]
Appliance replacement gasket, flush mount
[1] The trim skirt is outdoor
-
rated when used with the Model 449
electrical box.
[2] Not compatible with the trim skirts.
To synchronize horn-
strobe
operation, you must install a separate
synchronization source. See Table
3. When connecting the horn-
strobe
to a listed control panel, verify synchronization operation on the
compatibility lis
t for the corresponding panel.
Table 3: Compatible synchronization source models
Number
Description
SIGA
-
CC1S
GSA
-
CC1S
SIGA
-
CC2A
SIGA
-
MCC1S
GSA
-
MCC1S
SIGA
-
MCC2A
Auto
-sync output module
ADTG1M
-
RM
EG1M
-
RM
G1M
-
RM
MG1M
-
RM
XLSG1M
-
RM
ZG1M
-
RM
Genesis signal master -
remote mount
APS10*
APS6*
BPS10*
BPS6*
EAPS10*
EAPS6*
EBPS10*
EBPS6*
MIRBPS10*
MIRBPS6*
XLS
-
BPS10*
XLS
-
BPS
Booster or auxiliary power
supply
* Represents any number of additional characters
Installation
Install this device in accordance with applicable requirements and in
accordance with the local authorities having jurisdiction.
WARNING:
Electrocution hazard. To avoid personal injury or death
from electrocution, remove all sources of power and allow stored
energy to discharge before installing or removing equipment.
Notes
•
Electrical supervision requires that you break the wire run at each
terminal. Do not loop wires around the terminals.
•
You can mount the WG4 horizontally or vertically on either the wall
or ceiling; place the electrical box accordingly. See
Figure 1.
•
When using a 449 electrical box, discard the gasket that is shipped
with the box.
•
When using a trim skirt or a surface mount application, use the
gasket that comes with the WG4 unit.
— or —
For flush mount applications on a flat surface, use the WG4GSKT
gasket accessory.
To install the horn-strobe:
1.
Remove the cover from the
horn-
strobe
by first removing the six
cover screws. See
Figure 2, item 1.
firealarmresources.com
