background image

10

4. S P E C I F I C A T I O N S

• Accuracy is specified for a period of 1 year after calibration and at 18°C to 

28°C (64°F to 82°F) with relative humidity to 80%.

General

Voltages

D

DC

C  V

Vo

olltta

ag

ge

e

A

AC

C  V

Vo

olltta

ag

ge

e

• Input Impedance: 10M

.

• Frequency Range: 40Hz to 400Hz (for AC).
• Response: Average, calibrated in rms of sine wave.

Current

DC Current

MAXIMUM VOLTAGE

1000V DC or 700V AC

FUSE PROTECTION

mA: F 200mA/250V  10A: no

POWER SUPPLY

9V battery, NEDA 1604 or 6F22

OPERATING TEMPERATURE

0°C to 40°C (32°F to 104°F) 

STORAGE TEMPERATURE

-10°C to 50°C (14°F to 122°F)

RANGE

RESOLUTION

ACCURACY

200mV

0.1V

±(1.2% rdg ±3 digits)

2V

1mV

20V

10mV

±(0.8% rdg ±3 digits)

200V

100mV

700V

1V

±(1.2% rdg ±5 digits)

RANGE

RESOLUTION

ACCURACY

200

µ

A

0.1

µ

A

2mA

1

µ

A

±(0.8% rdg ±3 digits)

20mA

10

µ

A

200mA

100

µ

A

±(1.5% rdg ±2 digits)

10A

10mA

±(2.0% rdg ±5 digits)

RANGE

RESOLUTION

ACCURACY

200mV

0.1V

2V

1mV

20V

10mV

±(0.8% rdg ±2 digits)

200V

100mV

1000V

1V

±(1.2% of rdg ±3 digits)

5163600K_Instructions.qxd  17/09/2009  15:14  Page 10

Содержание MNT070

















Отзывы: