Edgetech USBL BROADBAND ACOUSTIC TRACKING SYSTEM Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 102

Edgetech USBL BROADBAND ACOUSTIC TRACKING SYSTEM Скачать руководство пользователя страница 102

SECTION 6:

MAINTENANCE

6-4

BATS

0018257_REV_A

Calibration Files

The hydrophone assembly is calibrated at EdgeTech. TrackMan uses the Hydrophone calibration files to
correct for the offsets within the Hydrophone. The calibration files consist of two binary files;
XXXXYYYY.bhi & XXXXYYYY.blo. These files contain offsets which compensate for hydrophone variances.
The CAL file’s first 4 characters are the Transceivers “Input & A/D” PCB S/N’s (if applicable) and the last 4
are Hydrophone S/N’s. The two file extensions: .blo (Binary Low byte 1-8 ) and .bhi (Binary Hi byte 9-16).
For example:

00001038.bhi

00001038.blo

If the Transceiver S/N’s are 0000 then the Hydrophone can be used with any BATS Transceiver. The CAL

Files reside on the TrackMan PC (Laptop) or Model 4451A under:

C:\Users\Public\Documents\ORE OffShore\Trackpoint MMI\CalFiles\InUseCAL\*.bhi

C:\Users\Public\Documents\ORE OffShore\Trackpoint MMI\CalFiles\InUseCAL\*.blo

When ordered as a system, these files are installed on an EdgeTech purchased PC. If a hydrophone

assembly is ordered separately, it comes with a USB Flash drive with a set of files, which must be installed

with the TrackMan Software onto the Customer-Supplied PC.
If a new Hydrophone is used with the system, the new Hydrophone’s set of Calibration files must be copied

into this directory.

NOTE:

Only one set of *.bhi & *.blo files can reside under this directory.

Move the older CAL files under a new directory called:

C:\Program Files\ORE Offshore\Trackpoint MMI\CalFiles\

OldCALFiles\

«
...
100
101
102

Содержание USBL BROADBAND ACOUSTIC TRACKING SYSTEM







































































































Отзывы:

Нет отзывов