Edge-Core ECS3510-28F Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 72

Edge-Core ECS3510-28F Скачать руководство пользователя страница 36

C

HAPTER

3

| Installing the Switch

Mounting

– 36 –

M

OUNTING

This switch can be mounted in a standard 19-inch equipment rack or on a
desktop or shelf. Mounting instructions for each type of site follow.

R

ACK

M

OUNTING

Before rack mounting the switch, pay particular attention to the following
factors:

◆

Temperature: Since the temperature within a rack assembly may be higher
than the ambient room temperature, check that the rack-environment
temperature is within the specified operating temperature range.

◆

Mechanical Loading: Do not place any equipment on top of a rack-mounted
unit.

◆

Circuit Overloading: Be sure that the supply circuit to the rack assembly is
not overloaded.

◆

Grounding: Rack-mounted equipment should be properly grounded.
Particular attention should be given to supply connections other than direct
connections to the mains.

To rack-mount devices:

1.

Attach the brackets to the device using the eight M4 screws provided in the
Rack-Mounting Kit.

«
...
34
35
36
37
38
...
»

Содержание ECS3510-28F









































































Отзывы:

Нет отзывов