Catalog #70024 & 70025
Brochure No. 63-0182
Page 2 of 6
©2008 Edelbrock Corporation
Rev. 6/08
INSTALLATION
1.
Install your new Victor Jr. Nitrous Plate using the supplied gaskets
on the carburetor pad of your intake manifold. Be sure that one
gasket is placed on the pad under the Victor Jr. Nitrous Plate and
one is placed on top of the plate under the carburetor. Be sure that
the plate is installed with the text on the plate facing the correct
direction as pictured to the right.
Failure to mount the plate
facing the correct way could result in catastrophic engine
damage.
2.
Re-Install the carburetor.
3.
Remove your current Performer RPM Nitrous Solenoid.
4.
Remove the 4AN x ¼” NPT inlet fitting from the solenoid. Install
one of the supplied 6AN x ¼” NPT Blue Filter Fittings into the inlet port of the Performer RPM Nitrous Solenoid using only Teflon Paste.
5.
Remove the 4AN x 1/8” NPT Blue outlet fitting from the Performer RPM Nitrous Solenoid. Install one of the supplied 4AN x 4AN x 1/8”
NPT Blue Tee fittings into the outlet fitting of the solenoid using only Teflon Paste.
6.
Re-install the Performer RPM Nitrous Solenoid onto the bracket in the engine compartment.
7.
Remove your current Performer RPM Fuel Solenoid.
8.
Remove the 4AN x 1/8” NPT Red outlet fitting from the Performer RPM Fuel Solenoid. Install
one of the supplied 4AN x 4AN x 1/8” NPT Red Tee fittings into the outlet fitting of the
solenoid using only Teflon Paste.
9.
Re-install the Performer RPM Fuel Solenoid onto the bracket in the engine compartment.
Pictured to the right is a properly assembled Performer RPM Nitrous Solenoid. Both your
nitrous and fuel solenoids should look like the one pictured above.
10.
Install the 6AN x ¼” NPT Blue Filter fitting into the inlet port of the new Performer RPM
Nitrous Solenoid using Teflon Paste only. Install the 4AN x 4AN x 1/8” NPT Blue Tee fitting
into the outlet port of the Performer RPM Nitrous Solenoid using Teflon Paste only.
11.
Install the assembled Performer RPM Nitrous Solenoid onto one of the supplied solenoid
brackets using the supplied solenoid bracket mounting screws. Mount this solenoid and
bracket as close to the Victor Jr. Nitrous Plate as possible on the opposite corner of the other
Performer RPM Nitrous Solenoid on the intake manifold. You may not want to solidly mount
the bracket yet until you have installed the nitrous hoses from the solenoid tee to the plate fittings. This may help to decide in the
mounting location of the solenoids due to line lengths.
12.
Install the 6AN x ¼” NPT Red fitting into the inlet port of the new Performer RPM Fuel Solenoid using Teflon Paste only. Install the
remaining 4AN x 4AN x 1/8” NPT Red Tee fitting into the outlet port of the Performer RPM Fuel Solenoid using Teflon Paste only.
13.
Install the assembled Performer RPM Fuel Solenoid onto the remaining solenoid bracket using the remaining 2 solenoid mounting
screws. Mount this solenoid and bracket as close to the Victor Jr. Nitrous Plate as possible on the opposite corner of the other
Performer RPM Fuel Solenoid on the intake manifold. You may not want to solidly mount the bracket yet until you have installed the
nitrous hoses from the solenoid tee to the plate fittings.
DISASSEMBLY
NOTE:
Be sure that the engine is cool, the fuel pressure has been relieved in the fuel system, and the battery has been disconnected.
1.
Remove the carburetor.
2.
Remove both lines from the plate to the solenoids.
3.
Remove the nitrous and fuel jet from the inlet fittings to the plate.
4.
Remove the Performer RPM Plate and gaskets from the carburetor pad of the intake manifold. Make sure that all of the gasket material
is removed from the carburetor pad of the intake manifold and the pad is clean and smooth.
