manualshive.com logo in svg

Edco TL-9 TURBO-LITE, Инструкция оператора

Поделиться
Скачать
Edco TL-9 TURBO-LITE Скачать руководство пользователя страница 13

TL-9-I-0715

13

301-638-3326 • edcoinc.com •  [email protected]

EQUIPMENT DEVELOPMENT COMPANY

FOR USE WITH DYMA-SLIDER SYSTEM

DOUBLE DIAMOND DOTS:

General Purpose Grind -

Removes general purpose epoxy, mastics, thinsets,
water-proofing coatings and more.

SINGLE DIAMOND DOTS:

Aggressive Grind -

Grinds and removes thick epoxies, weather-proofing
membrane and other coatings.

PCD ACCESSORY:

Extremely Aggressive

Removal - Digs through industrial strength
coverings, water-proofing membranes,
thick epoxies and much more -

Leaves a textured concrete surface.

EDCO ARROW:

Hard glue

removal, fast coating removal,
create smooth surfaces and more.

PEAKS:

General Purpose Grind -

Smoothes surfaces with fewer scratchs - Ideal for
concrete preparation and polishing. Removes thinsets,
concrete coatings and more.

Visit edcoinc.com to see all of our Quick-Change Accessories.
Accessories are subject to change.

Содержание TL-9 TURBO-LITE





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды