Edco SS-16A Скачать руководство пользователя страница 12

E-SS20/16A-I-0607

Printed in USA

©2007 

TVW

Page 12

100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone (301) 663-1600 • 1-800-638-3326
Fax (301) 663-1607 • 1-800-447-3326
Website: www.edcoinc.com 
Email: [email protected]

®

A Division of Equipment Development Company, Inc.

Check Engine Oil Before Each Operation - 

Check Engine Manufacturer’s Owner’s Manual for specifi c 

instructions.

Change Oil & Filter Every  50 Hours of Operation 
(Sooner if Necessary). 

Check Drive Chains Before Operation  - 
Lubricate Weekly

Open gas tank door - 
Drive chain is just inside, on the right.

Inspect/adjust Arbor Drive and 
Drive Belts - 

On new machines and 
after installation of new belts, 
adjust belt tension after the fi rst four hours, 
then as necessary.

Loosen engine mount bolts (2) 
turn jacking bolt to lift engine mount. (1) 

Note:
To change the drive belt, the engine must be 
slid forward. Loosen the engine bolts (4)
that hold the engine to the mount and slide 
the engine forward to its original position.  
Retighten the engine bolts and follow the 
directions above to retighten the arbor belts.

Drive Chain

Belts

Front 
Engine 
Mount
Bolts (2)

Remove

Belt Guard

Jacking 

Bolt

Arbor 

Belts

Drive 

Belt

Engine 

Bolts (4)

Содержание SS-16A













Отзывы: