Edco SS-16A Скачать руководство пользователя страница 10

E-SS20/16A-I-0607

Printed in USA

©2007 

TVW

Page 10

100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone (301) 663-1600 • 1-800-638-3326
Fax (301) 663-1607 • 1-800-447-3326
Website: www.edcoinc.com 
Email: [email protected]

®

A Division of Equipment Development Company, Inc.

Before Changing Blades:

Inspect all blades carefully before installing. Check for cracks, loose segments and oversize, worn, or 
out-of-round arbor holes (See page 13).  Do not use 

any

 questionable blade since serious personal injury 

and/or damage to property can result.  Do not use warped, twisted, or out-of-balance blades.  Unbalanced 
blades will wear excessively, vibrate and damage both arbor shaft and bearings. 

For safety reasons, EDCO 

does not

 recommend the use of any abrasive blades.  Abrasive blades can 

break and cause serious personal injury to operator and/or bystanders.  If abrasive blades are used by 
choice, only use those which are marked as 

reinforced 

abrasive blades. 

• 

Make sure you have the proper blade for the job. Determine the hardness and composition of the slab.  Give your 

dealer complete information including whether re-bars are present, the desired depth of the cut, and the length of the 
cut. If in doubt, contact the blade manufacturer.  Never exceed the maximum operating speed of the blade.  Be sure to 
match the blade speed rating with the arbor shaft speed on the machine.

Do not remove or lift the bladeguard unless 
blade has stopped completely and the engine is off.

Changing Blades:

• 

Raise blade guard and remove arbor shaft nut, washer

       and blade retaining cap. (

Figure 14

) Both the arbor shaft 

       nut and the fl at of the backing plate require a 1 1/2” wrench
       two are provided with the machine.

• 

Clean the arbor shaft, backing plate, and blade cap and  

 

inspect for damage or wear.  Make sure the arbor shaft  

 

threads are clean and undamaged.  If any damage is de 

 

tected, consult your EDCO dealer or the EDCO factory.

• 

Carefully place the blade on the arbor shaft and turn until

       the drive pin lines up with the hole in the backing plate.
 

(

Figure 11

) Do not use a blade without a drive pin. 

• 

Fit the washer and arbor shaft nut and retighten  

 

the nut using the two 1 1/2” wrenches. 

 

(

Figures 12 & 13

)

• 

Secure the blade guard in the operating 

 

position before starting engine. 

Figure 11

Figure 12

Figure 13

Figure 14

Arbor Shaft Nut

Washer

Blade Retaining 

Cap

Arbor Shaft

Backing Plate

Содержание SS-16A













Отзывы: