Edco HSS-14 Скачать руководство пользователя страница 8

E-HSS14-I-0517

EQUIPMENT DEVELOPMENT CO., INC.

Page 8

800-638-3326 • edcoinc.com • [email protected]

Look for “direction of rotation” markings on the new blade. 
(Usually an arrow stamped on the blade.) 

Place new blade on the arbor shaft verifying that the markings on the blade follow the 
proper direction of rotation. Blade should be positioned in the center of the dust chan-
nel. (

Figure 11

)

Reinstall and tighten bolt using a SAE 3/4” wrench. 

Reposition blade guard and tighten wing nuts.

Reconnect spark plug lead.  

Changing the Blade:

• 

Inspect the new blade thoroughly before installing.  Check for cracks, loose segments, worn or out-of-round arbor  

 

holes.  Refer to the 

Rx for Diamond Blades

 pamphlet provided with your blade for more detailed information on

       inspecting blades.  Be sure the blade is appropriate for the job and matches the arbor shaft speed & mounting
       confi guration on this saw. 

 

The HSS-14 was designed to be used with diamond saw blades only. It is a “fi xed head machine”, therefore it is

       important to use blades that will not wear down. Fiber blades will wear down and the cut will not go all the way
       through the work piece. In addition, for the vacuum system to operate properly when dry cutting, the blade must
       reach into the dust channel.

Move the rolling table out of the way to the back or front 
of the machine.  
Loosen the two wing nuts on the back side of the blade 
guard and rotate blade guard back and tighten to hold in 
guard in place. (

Figure 10

)

Loosen and remove arbor cap bolt.
Carefully remove old blade.
Inspect arbor shaft, backing plate and 
blade guard while blade is off .  
Clean if dirty or replace if damaged or worn.   

Maintenance

Disconnect spark plug lead before performing 

any maintenance on this machine.

Consult the 

Engine Manufacturer’s Owner’s Manual

  for more detailed engine maintenance instructions.

Figure 10

Figure 11

Содержание HSS-14













Отзывы: