Edco HSS-14 Скачать руководство пользователя страница 10

E-HSS14-I-0517

EQUIPMENT DEVELOPMENT CO., INC.

Page 10

800-638-3326 • edcoinc.com • [email protected]

Change Engine Oil:

• 

Check Engine Oil before each operation. Open the fi ller cap and look at the dip stick. (

Figure 15

 

Oil should be clearly visable both on the stick and in the cavity and should look fairly clean. Running the machine

      on dirty oil or when the oil is low will result in damage to the equipment.

• 

Change the Engine Oil after every 50 hours of operation - or sooner as conditions require.  Refer to the Engine 

       Manufacturer’s Owner’s Manual for specifi c viscosity recommendations and changing instructions. 

Inspect and Clean Oil Air Filter:

Shown with fi lter element. Outer foam fi lter is removable for cleaning. Refer to the Engine Manufacturer’s Owner’s 

Manual for instructions on specifi c models. Check air fi lter at least once daily. (Figure 16)

Dirt build up on the fi lter will cause the engine to wear faster. 

Dip Stick/

Filler Cap

Oil fi ller cap
 & Dipstick

Oil drain

Figure 15

Figure 16

Air fi lter cover 

Air fi lter element

NOTE: 

To remove air fi lter cover remove wing nut on top of fi lter cover and lift cover off  as shown in (Figure 16).

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing 

chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other 
reproductive harm.  If you are unfamiliar with the risks associated with the particular process and/or material being 
cut or the composition of the tool being used, review the material safety data sheets and/or consult your employer, 
the manufacturers/suppliers, governmental agencies such as OSHA and NIOSH and other sources on hazardous 
materials.  California and some other authorities, for instance, have published lists of substances known to cause 
cancer, reproductive toxicity, or other harmful eff ects.

Control dust, mist and fumes at the source where possible.  In this regard use good work practices and follow the recom-

mendations of the manufacturers/suppliers, OSHA/NIOSH, and occupational and trade associations.  Water should 
be used for dust suppression when wet grinding/cutting/drilling is feasible.  When the hazards from inhalation of dust, 
mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved 
by NIOSH/MSHA for the material being used.

Grinding/cutting/drilling of masonry, concrete and other materials with silica in their composition may give off  dust or 

mists containing crystalline silica.  Silica is a basic component of sand, quartz, brick clay, granite and numerous 
other minerals and rocks.  Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or 
fatal respiratory diseases, including silicosis.  In addition, California and some other authorities have listed respirable 
crystalline silica as a substance known to cause cancer.  When grinding/cutting/drilling such materials, always follow 
the respiratory precautions mentioned above. 

SMI Dust and Silica Warning

Содержание HSS-14













Отзывы: