background image

 

REV.1/25/05 

Page 5 of 9  Part #17810

 

 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

To attach wall cover plate to receiver box: 

 

 

 

 

 

1. 

Position the receiver as shown in diagram to the left with lower tab on 
wall cover plate into groove of receiver (Make sure ADJ hole 
and LEARN hole on cover plate properly aligns with remote receiver)  

2. 

Pull receiver up and snap into top tab of cover plate. 

 

3. 

Position the wall cover plate so the word ON is facing up. 

 

4. 

Install the remote receiver into the plastic switch box using the two  
long screws provided. Push the slide Button over the receiver slide 
switch only after making sure the remote receiver has LEARNED the  
transmitter’s security code (see MATCHING SECURITY CODES).  NOTE: slide    

 

button covers both ADJ and Learn holes when properly installed. 

 
 
 
 
NOTE:  The remote receiver will only respond to the transmitter when the 3-position  
slide button on the remote receiver is in the REMOTE position.  If the system does not  
respond to the battery transmitter on initial use, see MATCHING SECURITY CODES,  
and recheck battery positions in the remote receiver.   

 

 
 
 
HEARTH MOUNT 

 

The remote receiver can be placed on the fireplace hearth or under the fireplace, behind the control access panel.  Position where the 
ambient temperature inside the receiver case does not exceed 130

0

 F

NOTE: Black Slide Button is used for Hearth Mount applications. 

 

 
 
WIRING INSTRUCTIONS

 

 
A qualified electrician or a gas technician who is familiar with the gas appliance and gas valves that will be operated by this remote 
should install the remote control system.  Incorrect wiring connections 

WILL

 cause damage to the gas valve or electronic module 

operating the gas appliance and may also damage the remote receiver.   
 

 
 
WIRING MILLIVOLT VALVES 

 
The remote receiver is connected to the millivolt valve using the TH (thermostat) terminals on the terminal block on the millivolt gas 
valve.  Connect 18 gauge stranded or solid wires from the remote receiver to the gas valve. 
 

Operation of the remote receiver is similar to that of a thermostat in that both turn the gas valve on 
and off based on input signals.  A thermostat’s input signals are different temperatures.  The remote 
receiver’s input signals come from the transmitter. 
 
Connect each of the two wires leading from the TH and TH/TP terminals on the millivolt gas valve to 
either of the two wire terminals on the remote receiver.  Normally it does not matter which wires go to 
which terminal.   
 

 
 
 
 

Remote Receiver

MILLIVOLT

VALVE

REMOTE

OFF

LEARN

ADJ.

Frequency adjusting

        access hole

ON

Learning

 button

 

R

E

M

O

T

E

ON

OFF

LEARN

ADJ

.

REMOTE

ON

OFF

LEARN

ADJ.

WALL

Plastic Switch Box

Remote Receiver

Cover Plate

Receiver

Slide

Button

 

Remote Receiver

Cover Plate
(Rear View)

 

Содержание TRW-1










Отзывы: