manualshive.com logo in svg

ECS L4IBMG2, Руководство пользователя, Страница: 45 / 56

Поделиться
Скачать
ECS L4IBMG2 Скачать руководство пользователя страница 45

L4IBMG2 / L4IBMGL2 V1.0b 

41 

The IDE hard drive will spin down if it is not accessed within a specified length 
of time. Options are from 1 Min to 15 Min and Disable. 

Soft-Off by PWR-BTTN (Instant-Off) 

Under ACPI (Advanced Configuration and Power management Interface) you 
can create a software power down. In a software power down, the system can 
be resumed by Wake Up Alarms. This item lets you install a software power 
down that is controlled by the power button on your system. If the item is set 
to Instant-Off, then the power button causes a software power down. If the 
item is set to Delay 4 Sec. then you have to hold the power button down for 
four seconds to cause a software power down. 

CPU THRM-Throttling (50.0%) 

Use this item to specify the CPU speed (at percentage) to slow down the CPU 
when it reaches the predetermined overheat temperature. 

Wake-Up by PCI Card (Enabled) 

When this item is enabled, the system power will be turned on if there is any 
PCI card activity.  

Power On by Ring (Disabled) 

If this item is enabled, it allows the system to resume from a software power 
down or a power-saving mode whenever there is an incoming call to an in-
stalled fax/modem. You have to connect the fax/modem to the mainboard.  

Wake Up On LAN (Disabled) 

When set to Enabled, the system power will be turned on if the LAN port re-
ceives an incoming signal. You have to connect the fax/modem to the 
mainboard Wake On LAN connector for this feature to work.  

USB KB Wake-Up S3 (Disabled) 

If you are using a USB keyboard, and the ACPI suspend type is set to S3, you 
can enable this item to allow a keystroke to wake up the system from power 
saving mode. 

Resume by Alarm (Disabled) 

When set to Enabled, additional fields become available and you can set the 
date (day of the month), hour, minute and second to turn on your system. 
When set to 0 (zero) for the day of the month, the alarm will power on your 
system every day at the specified time. 

** Reload Global Timer Events ** 

Global Timer (power management) events are I/O events whose occurrence 
can prevent the system from entering a power saving mode or can awaken 
the system from such a mode. In effect, the system remains alert for anything 
that occurs to a device that is configured as Enabled, even when the system 
is in a power-down mode. 

 

Primary/Secondary IDE 1/0 (Disabled) 

Содержание L4IBMG2

























































Отзывы:

Нет отзывов