Ecreso Helios FM 20/100 W, Руководство пользователя

Страница: 49 / 80

Helios FM 20/100 W, user manual– 12/2011
Page 49
Head Office : Parc d’activites Kennedy - 20, avenue Neil Armstrong – F-33700 Bordeaux-Merignac (France)
Tel +33 (0)5 57 928 928 – Fax +33 (0)5 57 928 929 –
www.ecreso.com – contact@ecreso.com
6.2. Serial commands
6.2.1. System commands
NAME
Access
(R/W)
Possible value on the serial port
of the unit
Comments
SYS.RST W Reset of all parameters.
SYS.RST.CPU W "RST"
General reset of the µc. Sends the return
code: RST
SYS.RST.EXC W General reset of the exciter
SYS.RAZ W "RAZ" Reloads NVRAM default values
SYS.TYPE R xxx x=[A..Z;0..9] Unit type: example "G75" for Goliath 750 W
SYS.PCAP R [0..999]
Nominal power of the unit: example
"300"=>300 W
SYS.SOFTREL R xx.xx.xx x=[0..9] Software version: example "3.0.1"
SYS.SOFTREL.LIST R xx.xx.xx x=[0..9]
List of the exciter software versions
CPU;DSP;FPGA;IP;EXC;A/IP;TUN
SYS.HARDREL R xx.xx.xx x=[0..9] Hardware version: example "3.0.1"
SYS.NAME R/W XXXX X=[A…Z] Equipment name
SYS.TIME R/W HH:MM:SS Reads and sets the amplifier time
SYS.DATE R/W DD/MM/YY Reads and sets the amplifier date
SYS.LOCALCOM.SPEED R/W 9600,19200,38400,57600,115200 Speed of the front panel serial port
SYS.COM1.SPEED R/W 9600,19200,38400,57600,115200 Speed of the rear panel serial port 1
SYS.COM2.SPEED R/W 9600,19200,38400,57600,115200 Speed of the rear panel serial port 2
SYS.COM1.ECHO R/W "ON" or "OFF"
Adds the local echo on the rear panel serial
port
SYS.COM2.ECHO R/W "ON" or "OFF"
Adds the local echo on the rear panel serial
port
SYS.LOCALCOM.ECHO R/W "ON" or "OFF"
Adds the local echo on the front panel serial
port
SYS.PASSWORD R/W xxx x=[A..Z;0..9]
Password for the console and front panel
display. ‘NONE’ disables the password
SYS.PASSWORD.RESET R/W xxx x=[A..Z;0..9]
Creates a text string to unlock the password
if it has been forgotten
SYS.LOG R
SYS.CID R/W [0..31] Unit identifier used by the CAN bus.
SYS.DATE.CALIB R DDMMYYYY Date of the last calibration
SYS.SN R YYMMXXXX A,M,X=[0..9]
Serial number of the unit: Y => year, M =>
month, X => number
SYS.UPTIME R [0..99999999]
Indicates the number of working hours since
commissioning
SYS.OPT.LIST R RF,RC,AIP,TUN,IP,COM,REC List of implemented options
SYS.IP.ADR R/W XXX.XXX.XXX.XXX X=[0…9] IP address of the optional IP board
SYS.IP.MASK R/W XXX.XXX.XXX.XXX X=[0…9] IP mask of the optional IP board
SYS.GPIO.IN.ACT R XX X=[A..F;0..9]
Indicates the corresponding RC when
managed manually (see
SYS.GPIO.IN.MASK)
SYS.GPIO.OUT.ACT R/W XX X=[A..F;0..9]
Enables the corresponding RM when
managed manually (see
SYS.GPIO.OUT.MASK)
SYS.GPIO.IN.MASK R/W XX X=[A..F;0..9]
Sets the RC control either by the control
board or manually. Hexadecimal code: each
bit corresponds to an input. Ex: A1
(10100001) indicates the RC 1, 6 and 8 are
managed manually