ECR PENNCO 16 Series Скачать руководство пользователя страница 29

Страница: 29 / 36

Appendix A-2 - Vent Damper TroubleShooting

Problem

Possible Cause

Recommended Solution

NO POWER

Between 4 & 1
Between 4 & 2
Between 4 & 3
Damper OPEN
NO COMBUSTION

1. Is gas turned on
2. Operating limit, pressure control, low water cut off not on.

3. Blocked vent switch or flame roll out switch tripped

4. Loose or broken connection
5. Defective component in appliance after vent damper

1. Verify gas is on
2. Verify operating limit, pressure control or low water cut off is

3. Reset or replace blocked vent switch or flame roll out switch

4. Tighten, repair, or replace connection
5. Replace defective component in appliance

Damper Sticks

1. Damper blade obstruction
2. Damper pipe egg shaped, out of round/binding.
3. Crimped end of vent piece inserted in to far

1. Clear the obstruction
2. Restore to damper pipe to round, verify not binding.
3. Correct the condition

Damper Rotates

Continuously

1. Defective damper motor assembly

1. Replace damper motor assembly

Note

For troubleshooting only. Verify damper is in

open position. Use service switch to keep

damper in open position. Place jumper between

2 & 3. If appliance fires, remove jumper and

plug receptacle back into damper controller

plug. If appliance does not fire, replace damper

motor assembly. Do not replace pipe assembly.

If damper motor assembly is not available, place

service switch in hold open position. This should

keep damper in open position and allow customer

to have automatic heat. Return or replace the

motor assembly at your convenience. Motor

assembly carries 18 month limited commercial

warranty from the original date of purchase.

(Refer to form #4294 on website). Pipe

assembly is not warranted.

Trouble Shooting with Jumper Wire In Place

Содержание PENNCO 16 Series





































Результаты поиска

Содержание PENNCO 16 Series

Отзывы:

Похожие инструкции для PENNCO 16 Series

Бренды по названию

Популярные бренды

ECR PENNCO 16 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PENNCO 16 Series

Отзывы:

Похожие инструкции для PENNCO 16 Series

Бренды по названию

Популярные бренды