EcoWater ETF2100 PF, Руководство пользователя

Страница: 12 / 24

Programming Face Plate Timer
ECOWATER
S Y S T E M S
3
12
4. Press the RECHARGE DAYS keypad again to
display a flashing MOnday and ON (factory set re-
charge). As you did in step 3, use the SET keypad
to change the display from ON to OFF, or from OFF
to ON, as desired.
5. Press RECHARGE DAYS keypad to display a
flashing TUesday, WEdnesday, etc., each time us-
ing the SET keypad to display either ON or OFF as
needed.
2. Press and hold the VAC/RCHG keypad for three
seconds until RCHG begins to flash in the display,
starting a backwash. This backwash flushes “fines”
from the new mineral, and purges air and bleach, re-
maining from the sanitizing procedure. The filter re-
turns to service in about 45 minutes.
3. RESTART THE WATER HEATER: Turn on the
electric or fuel supply to the water heater, and light
the pilot, if applies. Note: The water heater is filled
with unfiltered water and, as hot water is used, it re-
fills with filtered water. In a few days, hot water will
be fully filtered. To have fully filtered water immedi-
ately, wait until the recharge (step 2 above) is over.
Then, drain the water heater until water runs cold.
THE SOLID STATE TIMER IS NOW PRO-
GRAMMED AND INSTALLATION IS COMPLETE.
FEATURES / OPTIONS
RECHARGE NOW -- For an immediate extra back-
wash at any time, use this feature. Press and hold
in the VAC/RCHG keypad for three seconds until
RCHG flashes in the display. The filter backwashes
for 25 minutes, followed by a 5 minute fast rinse
cycle. Then the filter returns to service.
VACATION -- The day you leave on vacation, or oth-
er long absence, press (DO NOT HOLD IN) the VAC/
RCHG keypad. VAC begins to flash in the display.
The timer will keep time, but the filter will not back-
wash and waste water.
Note: While in the VACATION setting, the filter will
go through a backwash if the RECHARGE NOW
feature is used (see above).
WHEN YOU RETURN, press the VAC/RCHG key-
pad again to return the filter to service, and the cor-
rect time of day in the display. Remember to to this
or the filter will not backwash and you will soon
have unfiltered water.
DOUBLE BACKWASH
-- Although available on this
timer, a double backwash cycle is not normally need-
ed with a sediment, taste and odor, or neutralizing fil-
ters. To set, if desired...
1. Press and
hold SET untill
18:88 shows in the display..
2. Press CURRENT TIME
AND DAY to display 3
dashes.
3. Press SET to display
dbl .
4. Press CURRENT TIME
AND DAY to display 18:88.
5. Press SET to return present time.
To cancel double backwash, repeat the above
steps. Displays for dbl and -- -- -- occur in reverse or-
der.
TIMER “POWER--OUTAGE MEMORY” -- If electri-
cal power to the timer goes off, the “memory”built
into timer circuitry keeps all settings for at least two
days or more. The display is blank and the filter will
not backwash. When electrical power comes on,
one of two things will happen.
1. The present time of day will show, meaning the
timer memory has kept all settings.
Note: If the filter was in a backwash when power
was lost, it will now finish the cycle.
2. The display will show a time, but it will be flashing.
The timer memory did not keep the time settings and
they must be reset.
The flashing display is to remind you to reset the
timer.
Notes:
When power comes on, the flashing display returns
to a time of 12:00 AM SUnday, then begins to keep
time again. If you do not reset all time settings, the
filter will backwash three days each week (default
time). However, backwash may be on the wrong
days and at the wrong time.
If the filter was in a backwash when power went off,
the valve will return to service position without finish-
ing the cycle. If your water is unfiltered, use the RE-
CHARGE NOW feature to start another cycle.