background image

32

This manual is the intellectual property of Ecosoft. Copying and reprinting is prohibited. © 2016

INSTALLER AND USER GUIDE FOR REVERSE OSMOSIS SYSTEM ECOSOFT ROBUST 1000, ROBUST 3000

ROBUST 3000

Water inlet

connection

Sediment

pre-filter

Inlet solenoid valve

Inlet pressure

gauge

Low-pressure

switch 

Booster

pump

Membrane

module

Operating

pressure

gauge

Flow restrictor

Drain outlet

High-pressure

switch

Carbon

post-filter

Tank

connection

Permeate outlet

Figure 3

Technological  scheme  of  RObust  3000  is  shown  in  Figure  2.  After  the  pre-filters,  the  pressure 

booster  pump  feeds  the  water  to  the  reverse  osmosis  membrane  array.  Permeate  from  both 

modules goes to the permeate collector, and the concentrate from the 1

st 

module goes to the 2

nd

 

one. Second stage permeate goes to the permeate collector, and concentrate is discarded to drain 

via concentrate flow restrictor and drain port in port rack. Pressure gauge no. 2 shows pressure 

between two membranes. Permeate goes to the purified water line or pressure tank (if installed), 

passing through the carbon post-filter. Purified water line may go to the purified water faucet (not 

included) or be connected with some other consumer appliance. High-pressure switch installed 

before the post-filter reads pressure in permeate line and starts the reverse osmosis system when it 

drops (due to taking of some water from the pressure tank or opening purified water faucet). When 

the system switches on, entry solenoid valve is opened and booster pump is powered up, which 

allows to feed water into the system. When purified water stops being drawn from the system, 

pressure starts to build up and closes high-pressure switch switching off the system.
RObust  3000  system  has  low  feed  water  pressure  protection  implemented  with  a  low-pressure 

switch,  which  prevents  the  pump  and  solenoid  from  operating  if  feed  pressure  is  less  than  

0.4 bar (5.8 psi). Two pressure gauges on the front panel show operating pressure in the system, 

which allows diagnosing potential and occurring problems.

Содержание ROBUST 1000


























Отзывы: