EcoSmart ESF.2.B.G16, Инструкция по установке, эксплуатации и обслуживанию

Страница: 13 / 28

© Copyright 2004 - 2020 EcoSmart Inc. All rights reserved. V0120
Burner Assembly - Propane
PROPANE
1. Unpack burner box. Remove all items and check against the items
listed on page 9 of the manual to ensure all parts needed are ready.
2. THE BURNER IS SHIPPED FOR PROPANE FUEL SOURCE. Verify
that you have the correct orifice installed by checking it against the fuel
orifice chart on page 1. The orifice has the number stamped on the side.
Once confirmed, check that the attached flexible gas line is tightly attached.
Ensure that the air shutter is open ¼” (6.4mm) on each side of the air shutter.
1/4’’
(6.4mm)
2.THE BURNER IS SHIPPED FOR PROPANE FUEL SOURCE. Verify that you have the correct orifice installed by checking it against the fuel orifice
chart on page 1. The orifice has the number stamped on the side. Once confirmed, check that the attached flexible gas line is tightly attached.
Ensure that the air shutter is open 1⁄4” (6.4mm) on each side of the air shutter.
3. Ensure ignitor wire is secured to bottom of Ignitor.
4. Ensure grounding wire is secured to bottom of burner.
3.Ensure the ignitor wire is secured to the bottom of the ignitor.
4.Ensure the grounding wire is secured to bottom of burner.
5. Linear burners only: (this step is not required for round burners)
Carefully place the Metal tray into the unit opening.
5.Linear burners only: (this step is not required for round burners)
Carefully place the Metal tray into the unit opening.
6. Position the burner assembly so that the gas input flexible line
(where the orifice is located) is pointing towards the control plate
cutout location of the surround. Carefully uncoil the thermocouple
tube. Feed the flexible gas line, thermocouple tube, grounding wire
and the ignitor wire through the burner location opening first then
place lower the burner into its final location. Install the grommet by
sliding it into the slot, place the burner into its final position.
6.Position the burner assembly so that the gas input flexible line (where the
orifice is located) is pointing towards the control plate cutout location of
the surround. Carefully uncoil the thermocouple tube. Feed the flexible gas
line, thermocouple tube, grounding wire and the ignitor wire through the
burner location opening first then place lower the burner into its final
location. Install the grommet by sliding it into the slot, place the burner
into its final position.
7. Round burners only: (this step does not apply to linear burners) insert
the metal tray to the Surround Unit. Carefully place the burner on the
Surround Unit near the tray opening – without inserting the burner into
the final location. Rotate the burner to make sure the thermocouple tube
is aligned with the slot on the tray/surround. The gas input flexible line
should be pointing 90 degrees from the gas control valve location of the
surround. Carefully uncoil the thermocouple tube. Feed the flexible line,
thermocouple tube, grounding wire and the ignitor wires through the
burner location opening first then lower the burner into its final location.
7. Round burners only: (this step does not apply to linear burners)
insert the metal tray to the Surround Unit.
8. Slide the black propane tank hose under the surround unit and out
through the control panel opening. The other end of the black propane
hose with the regulator will attach to the propane tank.
8.Slide the black propane tank hose under the surround unit and out through the control panel opening. The other end of
the black propane hose with the regulator will attach to the propane tank.
9. Pull all hoses and wires from inside the unit out through the control
plate cutout.
9.Pull all hoses and wires from inside the unit out through the control plate cutout.