EcoNet UETST700SYS, Руководство пользователя

Страница: 15 / 69

EcoNet
®
Smart Thermostat User Guide
15 > Return to Table of Contents
Settings (con’t)
Humidification (Menu > Settings > Humidity > Humidification)
Enable Humidification –
The system can control a humidifier attached to the
furnace or air handler to increase humidity in the space. It is important to note
you cannot humidify above the dehumidification set point.
Humidification Set Point – This setting allows you to choose the indoor
relative humidity desired, under which humidification will activate. The default is
humidification set point is 30% and is configurable between 15 and 45%.
Humidify During –
Select the modes in which humidification will be
performed. Humidification can occur during heating, continuous fan and/or
cooling mode.
• Heat – Humidifier will operate with equipment during Heat if a
humidification demand is present.
• Heat/Fan –
Humidifier will operate with equipment during these modes if a
humidification demand is present.
• Heat/Fan/Cool – Humidifier will operate with equipment during these
modes if a humidification demand is present.
Smart Control –
Smart Control is used to reduce or prevent water
condensation on the inside of windows while humidifying in the winter season.
The control monitors indoor and outdoor temperatures and reduces the
humidification percentage according to the Smart Control level chosen by the
user. Start out with the Low setting. If objectionable condensation occurs on
windows, choose the Medium or High setting.
Humidify With Fan – If there is a call to humidify and the fan and heating/
cooling are off, the fan will be forced on to humidify. Select the desired fan
speed from Low to High.
Note: Humidification is only available if a humidifier is installed.
How to Test a Humidifier
Adjust the humidify set point up to ‘TEST’, select Humidify during “Heat/Fan”, then turn on a continuous fan speed
on the Fan screen under Settings. This should force the humidifier to run. This setting will last for 30 minutes, where
the maximum setting will return to 4% below the dehumidification set point.
Away Settings (Menu > Settings > Away)
Your system will follow the customized heating, cooling and fan settings when
you place your system into ‘Away’ mode. The system can be placed into Away
by selecting the Home icon (closed door) on the home screen. Once the system is
placed into Away mode it will remain until canceled. Simply tap the Away icon
(open door) to exit Away mode. The system will resume the schedule or return to
the previous settings if a schedule is not being followed. You can also exit Away
by increasing or decreasing the temperature.
Note: If your system is in Cool or Heat when placed into Away mode your system will only manage
to the respective Away set point.
71
47%
68
OFF
Dining Room
Zone 3
Away
Backlight Enabled?
Outside Temp Selection?
BACK
Basic Settings
Internet
Yes
36
UNITS
34
Group 1
Refrigeration
!
61%
72
Basement
Zone 4
85
80
Zoning System Test
T957_O Low Refrigerant Pressure
BACK
Installer Checkout
Linearize Dampers
21
status: Setting airflow CFM: 840
54
75
44%
80
65
Away
Resume Schedule
71
Home 44%
70
80
Cooling to
Enable Humidification?
Humidify Set Point
Humidify During...
Smart Control
Humidity With Fan
BACK
Humidification
30 %
Heat
Off
Off
No
71
47%
68
OFF
Dining Room
Zone 3
Away
Backlight Enabled?
Outside Temp Selection?
BACK
Basic Settings
Internet
Yes
36
UNITS
34
Group 1
Refrigeration
!
61%
72
Basement
Zone 4
85
80
Zoning System Test
T957_O Low Refrigerant Pressure
BACK
Installer Checkout
Linearize Dampers
21
status: Setting airflow CFM: 840
54
75
44%
80
65
Away
Resume Schedule
71
Home 44%
70
80
Cooling to
Enable Humidification?
Humidify Set Point
Humidify During...
Smart Control
Humidity With Fan
BACK
Humidification
30 %
Heat
Off
Off
No
71
47%
68
OFF
Dining Room
Zone 3
Away
Backlight Enabled?
Outside Temp Selection?
BACK
Basic Settings
Internet
Yes
36
UNITS
34
Group 1
Refrigeration
!
61%
72
Basement
Zone 4
85
80
Zoning System Test
T957_O Low Refrigerant Pressure
BACK
Installer Checkout
Linearize Dampers
21
status: Setting airflow CFM: 840
54
75
44%
80
65
Away
Resume Schedule
71
Home 44%
70
80
Cooling to
BACK
Settings
Installer
Away
Humidity Time Basic
Vacation Fan