background image

26

Note:

The prevailing operating manual, EC Declaration of Conformity and the Ex-certificate 
can be downloaded from the relevant product page under 

www.ecom-ex.com

 or they 

can be requested directly from the manufacturer.

1. Application

The Ex-MX4 BT is a contactless temperature measuring device with an integrated 
Bluetooth™ and is designed for industrial use in potentially explosive areas of Zones 2 
and 1 in accordance with Directive 99/92/EC (ATEX 137). 

2. Safety instructions

This operating manual contains information and safety regulations that must be 
followed to ensure the safe and reliable operation of the device under the described 
conditions. Non-observance of the information and instructions can have dangerous 
consequences or may contravene applicable regulations.

Please take the time to read through the operating manual carefully before you 
start using the device.

The German version of this operating manual shall prevail in the event of any doubt or 
discrepancies (for example, due to translation or printing errors).

3. Errors and load restrictions

If there is a possibility of the safety of the device being hampered, the device must be 
taken out of operation and removed from the Ex-area immediately.
Accidental re-commissioning of the device must be prevented.
We recommend sending the device to the manufacturer for examination.

The safety of the device may be at risk if, for example:
-  damages are visible on the casing
-  the device has been subjected to excessive loads for which it is not designed
-  the device has been improperly stored
-  the device has been damaged in transit
-  labels on the device are illegible
- malfunctions occur
-  obvious measuring inaccuracies occur
-  measurements using the device are not possible any longer
-  permitted threshold values have been exceeded

4. Safety regulations

Persons using the device must observe the standard safety regulations and read the 
certificate to prevent incorrect operation of the device.

The following safety regulations must be observed in addition:

-  The device must not be opened inside the Ex-area.
-  The batteries must be changed only outside the Ex-area.
-  Additional batteries must not be carried in the Ex-area.
-  Only the approved battery types must be used.

Содержание Ex-MX4 BT





















Отзывы: