background image

ecoSMART Supervisor user, installer and technical service manual 

 

 

 

38 

 

EN

 

10.

 

Warranty and technical service 

10.1.

 

Manufacturer's warranty 

ECOFOREST  is  liable  for  lack  of  conformity  of  the  product  or  its  spare  parts,  in  compliance  with  the  current  regulations  of  the 
country where the product is purchased. The warranty is only valid in the country where the product is purchased. 

In  addition,  with  previous  consent  from  ECOFOREST,  the  local  authorised  distributor  can  offer  an  extension  of  the  warranty 
established by current legislation. 

Conditions and validity of the warranty 

In order for this warranty to be considered valid the following conditions must be verified. 

 

ECOFOREST must allow the product under warranty to be sold in the country where it is going to be installed. 

 

The product under warranty must be used exclusively for the purpose that it was designed for. 

 

All  installation,  start-up,  maintenance  and  repair  work  carried  out  on  the  equipment  must  be  performed  by  a  technical 

service authorised by ECOFOREST. 

 

All  replacement  of  parts  must  be  carried  out  by  a  technical  service  authorised  by  ECOFOREST  and  always  with  original 

ECOFOREST spare parts. 

 

The purchaser must inform the establishment that sold the product of the lack of conformity within 30 (thirty) days. 

 

For the warranty to be effective, the purchaser must present a legal document that supports the date of purchase from the 

establishment that made the sale. 

Disclaimer of warranty 

The warranty does not include product non-conformities derived from: 

 

Weather conditions, chemical agents, improper use and other causes that do not depend directly on the product. 

 

Installation and/or handling of the equipment by unauthorised personnel. 

 

Improper transportation of the product. 

 

Part wear due to normal equipment operation, unless due to a manufacturing defect. 

Request for service under warranty 

A request for service during the warranty period must be presented at the establishment where the product was purchased. 

Product returns will only be accepted if previously accepted in writing by ECOFOREST. 

The  product  must  be  returned  in  its  original  packaging  and  with  a  legal  document  that  supports  the  date  of  purchase  from  the 
establishment that made the sale. 

 

10.2.

 

Authorised distributors and technical service 

ECOFOREST has an extensive network of authorised  companies that distribute and perform the technical service on its products. 
This  network  will  provide  our  customers  with  all  the  information  and  technical  support  they  need,  anywhere  and  under  any 
circumstance. 

Содержание ecoSMART Supervisor









































Отзывы: