Eclipse EGO9 Скачать руководство пользователя страница 17

Страница: 17 / 45

ACCESSING THE MENU

SYSTEM

to access the main menu from the run screen double-

click the button and the first item on the main menu

will be displayed. Alternatively, push and hold the

button for 2 seconds.

to access the set-up menu from either the run screen

or the main menu push the internal button and the first

item on the set-up menu will be displayed.

MOVING AROUND THE

MENUS

press and release the button to display the

next item on the menu. when the last menu item is

displayed, pressing the button will display the first

item.

press and release the button to display the previous

item on the menu. when the first menu item is

displayed, pressing the button will display the last

item.

when the displayed item is a branch, as indicated

by an animation on the right of the screen, press the

button to move to another menu.

ALTERING pARAMETERS

when the displayed item is a parameter, as indicated by

a parameter value on the right of the screen, pressing

the button will activate the Edit mode which allows

the parameter value to be altered. when

Edit mode is active, edit indicators

appear on the left of the screen as shown

in the screen below.

there are two types of parameter,

numeric parameters and choice

parameters.

A numeric parameter has a value which

is a number whereas a choice parameter

is one that has a small number of distinct

choices. Altering parameter values is

essentially the same for both types of parameter.

to alter a numeric parameter, first activate the Edit

mode. press the button to increase the parameter

value one step at a time. press and hold the button

to increase the parameter value rapidly. when the value

reaches it’s maximum it will revert to it’s minimum

value. press the button to decrease the parameter

value one step at a time. press and hold the button

to decrease the parameter value rapidly. when

the value reaches it’s minimum it will revert to it’s

maximum value. when the required parameter value is

displayed press the button to accept the value and

end the Edit mode.

to alter a choice parameter, first activate the Edit mode.

press the button to display the next choice in the

list. when the last choice is displayed, pressing will

display the first choice in the list. press the button

to display the previous choice in the list. when the first

choice is displayed, pressing the button will display

the last choice in the list. when the required choice is

displayed press the button to accept the choice and

end the Edit mode. if the displayed choice is cancel

then pressing the button will end the Edit mode

and restore the parameter to the value that is was prior

to editing.

NOTE:

if thE tournAmEnt lock is sEt to ‘off’ thEn thE

mAin mEnu And sEt-up mEnu ArE joinEd togEthEr

which mEAns thAt thEy cAn bE AccEssEd in EithEr of

thE two wAys AbovE.

THE MAIN MENU

the main menu comprises parameters that do not

affect the way in which the Ego9 shoots and which

therefore do not have to be tournament locked.

from the run screen push and hold the button.

initially, the current preset configuration will be

displayed and then after one 1 second

OFF?

will be

displayed, the first item on the main menu.

to turn off the Ego9, select the

OFF?

branch or pull the

trigger while the

OFF?

branch is displayed.

to return to the run screen, select the

EXIT

branch.

DISpLAY

THE DISpLAY pARAMETER

this parameter is used to select the information that is

displayed on the left of the run screen. this parameter

has the following choices:-

TIMER:

the game timer is displayed on the run

screen

SHOTS:

the shot counter is displayed on the run

screen

AVG ROF:

the Average rate of fire is displayed on

the run screen

pEAK ROF:

the peak rate of fire is displayed on

the run screen

CANCEL:

Editing is cancelled and the parameter

remains unchanged.

this parameter differs from most others in that once

a choice has been made then the Edit mode is ended

and the display returns to the run screen.

NOTE:

if thE lock option is disAblEd furthEr options

will bE displAyEd in thE mAin mEnu.

EDIT INDICATORS

32.

-U

CONTENTS

ORIENTATION

QUICK SET-UP

USING YOUR EGO9

ADVANCED SET-UP

MENU TREE

MAINTENANCE

FAULT FINDING

SERVICE CENTERS

PARTS LIST

SPARES & ACCESSORIES

33.

-U

ADVANCED SET-UP

QUICK GUIDE

Содержание EGO9














































Результаты поиска

Содержание EGO9

Отзывы:

Eclipse EGO9, Руководство оператора, Страница: 17 / 45

Результаты поиска

Содержание EGO9

Отзывы: