background image

Eclipse ImmersoJet v2.20 Design Guide 330,  10/02

Safety

2

In this section you will find important notices about safe
operation of a burner system.

d

Danger:

The burners covered in this manual are designed
to mix fuel with air and burn the resulting
mixture.  All fuel burning devices are capable of
producing fires and explosions when improperly
applied, installed, adjusted, controlled or
maintained.

Do not bypass any safety feature;  You can cause
fires and explosions.

Never try to light the burner if the burner shows
signs of damage or malfunctioning.

w

Warning:

The burner is likely to have HOT surfaces. Always
wear protective clothing when approaching the
burner.

n

Note:

This manual gives information for the use of these burners
for their specific design purpose. Do not deviate from any
instructions or application limits in this manual without
written advice from Eclipse Combustion.

Read this entire manual before you attempt to start the
system.  If you do not understand any part of the information
in this manual, then contact your local Eclipse representative
or Eclipse Combustion before you continue.

I

NTRODUCTION

S

AFETY

9

Содержание ImmersoJet Series

























Отзывы: