EcLine EC-PM-530D Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 82

EcLine EC-PM-530D Series Скачать руководство пользователя страница 68

EC-PM-530D User's Manual

- 61 -

Bit image data

The first pin

The eighth pin
Print data

m: Ending ASCII code of user-defined character set. m

≤

127. The number of user-defined

characters is m-n+1, and the maximum number is 96. When user defines only 1
character, m=n.

a: The byte number of user-defined characters.

d1 d2…db: The data of user-defined characters. Every character has s×a bytes. m-n+1 characters

altogether have (s×a) × (m-n+1) bytes (b=(s×a) × (m-n+1)).
The user-defined characters after being defined will be valid all the time until they are
defined again or the printer is turned off.

The format of each user-defined character data is shown as follows:

d1 d4

…

d2 d3

…

ESC * Select bit-image mode

Format: ASCII: ESC * m n1 n2

［

d

］

n1+256

×

n2

Decimal: 27 42 m n1 n2

［

d

］

n1+256

×

n2

Hex: 1B 2A m n1 n2

［

d

］

n1+256

×

n2

Description:
This command is used for setting dot matrix figure mode (m) and setting the transverse dots number (n1,
n2) of dot matrix figure.
m=0, 1
0

≤

n1

≤

255, 0

≤

n2

≤

3, 0

≤

d

≤

255.

n1, n2 is hexadecimal figure with two bits. n1 is low byte and n2 is high byte. n1, n2 is used for denoting the
transverse dots number of figure printed by “ESC

*” command. This value should be within the number of

maximum line-width dots.
When m=0, normal printing is selected, the maximum number of printing dots is 210.
When m=1, half-dot printing is selected, the maximum number of printing dots is 420. On this condition the
adjacent dots cannot be “1” at the same time.
The definition of [d] is:

ESC - Set English underline mode

Format: ASCII: ESC

-

n

Decimal: 27

45

n

Hex: 1B

2D

n

Description:
Set English underline mode
n=0, turns off underline mode; n=1, turns on underline mode.

b7

«
...
66
67
68
69
70
...
»

Содержание EC-PM-530D Series



















































































Отзывы:

Нет отзывов