Echotrek SE-300 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 52

background image

10

SE/SG-300 series two-wire compact ultrasonic level transmitters

5.

PROGRAMMING

The EchoTrek can be programmed by the following two ways:

•

Programming without Display Module

see 5.1.

Assignment of the levels to the 4 and 20 mA current output, error indication by the analogue signal and damping can be set.

•

With the

SAP-200 Display Module

, see 5.2.

All features of the unit can be set, such as measurement configuration and optimisation, 32-point linearisation, dimensions
for 11 tanks with different shape and for 21 different open channels (flume, weir, etc).

Devices with the type number

EchoTREK SG...

are already equipped with the SAP-200.

The EchoTREK is fully operational without the SAP-200. The SAP-200 is only needed for programming and/or displaying measurement values.

The unit will measure during programming in accordance with the previous parameters. The new, modified parameters will only be effective after
returning to the Measurement Mode

If the transmitter is left in Programming Mode by mistake, it will automatically return to Measurement Mode after 30 minutes and will operate with the parameters
entered during the last completed programming.

The EchoTREK will be delivered with the following

Factory Default

:

⇒

Current output, display and bargraph: LEVEL

⇒

Current output and bargraph proportional to the level

⇒

4 mA: assigned to the minimum level 0%

⇒

20 mA: assigned to the maximum level 100%

⇒

Error indication by the current output: hold last value

⇒

Damping: 60 sec

«
...
12
13
14
15
16
...
»

Содержание SE-300 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для SE-300 Series

Бренд: Easy wave Страницы: 2

DRAW WIRE SFP Series

Бренд: Lika Страницы: 2

Бренд: SICK STEGMANN Страницы: 8

Бренд: Maico Страницы: 24

FT DX 9000 - CAT OPERATION REFERENCE BOOK

Бренд: Yaesu Страницы: 20

CARBOCAP GMM112

Бренд: Vaisala Страницы: 2

Бренд: CommRadio Страницы: 27

Бренд: Sencore Страницы: 3

Бренд: E+E Elektronik Страницы: 4

Бренд: Alead Страницы: 12

FLOWLINE US01 Series

Бренд: Echotouch Страницы: 64

Бренд: M-system Страницы: 2

Бренд: Intek Страницы: 36

Бренд: Midland Страницы: 24

Бренд: Midland Страницы: 36

Бренд: Midland Страницы: 58

Бренд: WIKA Страницы: 140

Бренд: Listen Technologies Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды