background image

Attention and Warning Symbols

You 

must

 be aware of safety when you install and use this system. This guide provides various procedures. 

If you do some of these procedures carelessly, you could 

injure

 or 

kill

 yourself or damage equipment or 

property. Some other procedures require special attention.

Important Safety Instructions

You 

must

 keep safety in mind when you install and use the DISH Pro Plus Twin LNBF. Refer to the safety 

instructions in the installation instructions that came with your system. In this guide, the following notes 
tell you when you need to pay special attention:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

Keep the following in mind when you install the DISH Pro Plus Twin LNBF:

Before you drill any holes in your building, make sure there are no wires or pipes near the holes.

Install the equipment in accordance with the local building and electrical codes. If you aren’t sure, call 
a licensed building inspector or electrician for help. 

Never install the satellite dish near power lines.

Don’t install the satellite dish on composite materials such as strand, chip, fiber, or particle board 
unless the fastener attaches securely to a wall stud, rafter, or other foundation material beneath the 
surface.

Marks a procedure where the following may happen:

• Personal injury or death may occur.
• Equipment or property may be damaged.

Marks the following issues:

• Important operation or maintenance instructions follow.
• Special attention is required.

Содержание DISH Pro Plus Twin LNBF


























Отзывы: