background image

6

3M (10 FT.)

After Refueling;

• Wipe any spilled fuel from the unit.
• Move at least 3 M (10 ft.) from refueling location before starting.

After Use;

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return

unused fuel to an approved fuel storage container.

PERSONAL

 

CONDITION

 

&

 

SAFETY

 

EQUIPMENT

WARNING  

  DANGER

Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly
and or safety precautions are not followed.  Proper clothing and safety gear must be worn when operating a
trimmer.

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE requirements
whenever you operate the trimmer.

Hand Protection

Wear no-slip, heavy duty work gloves to improve your grip on the
Trimmer/Brush Cutter handles.  Gloves also reduce the transmission of
machine vibration to your hands.

Hearing Protection

ECHO recommends wearing hearing protection whenever unit is used.

Содержание SRM-3100 Series









































Отзывы: