background image

16

X7502026204

© 04/2014 ECHO Inc.

ASSEMBLY

SRM-266U

4. Insert Cotter Pin (C) in hole in PTO shaft, and bend pin legs 

around shaft counterclockwise to retain 10 mm nut.

Never reuse a cotter pin - install a new cotter pin each time a blade 
is installed or replaced.

5. Remove locking tool (G).

U-Handle Installation

1. Install upper U-Handle and bracket on lower bracket with 

one (1) 8mm x 55mm bolt (N) and (1) large circular washer. 
Do not tighten bolt securely until final adjustments are 
completed.

2. Loosen upper (2) U-handle clamp screws (O), and position 

U-handle as shown.

3. Lightly tighten 8mm bolt (N) and clamp screws (O) to hold 

U-handle in position until final adjustments are completed.

4. Route throttle linkage and ignition lead assembly along shaft and clip as shown.

5. Install throttle linkage cable into fan cover clip (C), if 

required.

Throttle Linkage and Ignition Leads

1. Close choke and remove air filter cover.

2. Place throttle linkage (C) through adjustment fixture (D) and 

install wire end into large carburetor throttle swivel hole (E). 
Check throttle for freedom of movement and that wide open 
throttle / low idle extremes are adjusted properly.  The 
throttle linkage must be adjusted by moving the adjustment 
fixture (D).  Consult with your Echo Dealer for correct 
adjustment procedure.

Parts Required:

U-Handle, Clamp w/screws, 8 mm x 55 mm hex 
bolt, 8 mm flat washer

A

G

M

E

D

C

20

N

O

C

C

D

E

Содержание SRM-266U









































Отзывы: