background image

6

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas.  Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended or twisted position.

Instead try to maintain a straight wrist position.  Also, when grasp-
ing, use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive move-

ment.

• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if

you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.

EQUIPMENT

WARNING  

  DANGER

Use only ECHO approved attachments. Serious injury may result
from the use of a non approved attachment combination. Read and
comply with all safety instructions listed in this manual and safety
manual. ECHO, INC. will not be responsible for the failure of
cutting devices, attachments or accessories which have not been
tested and approved by ECHO.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or

replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO

NOT operate unit if leaks are found.

• Inspect shield for damage and ensure that the cut-off knife is

securely in place. Replace if either is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe

operating condition.

• Check that front (loop) handle and optional shoulder/waist harness

are adjusted for safe, comfortable operation. See Assembly for proper
adjustment.

Содержание SRM-260 - 12-03





























Отзывы: