background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

3

INTERNATIONAL

 

SYMBOLS

Hot

Surface

Carburetor

Adjustment

- Idle speed

Carburetor

Adjustment

- High speed

mixture

DESCRIPTION

SYMBOL

SYMBOL

"WARNING, SEE

OPERATOR'S

MANUAL

Wear eye, ear

 and head

protection

Emergency

Stop

Fuel and oil

mixture

Finger Severing

Carburetor

Adjustment
- Low speed

mixture

Primer

Bulb

Ignition

ON/

OFF

Wear hand and
foot protection

Safety/Alert

Keep bystanders and helpers

away 15 m (50 ft.).

DO NOT smoke

near fuel.

DO NOT allow

flames or sparks

near fuel.

DESCRIPTION

SYMBOL

DESCRIPTION

SYMBOL

DESCRIPTION

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"Run"

Position

(Choke Open)

Do not use

blades. String

line only

IMPORTANT
The enclosed message provides
information necessary for the protec-
tion of the unit.

NOTE
This enclosed message provides tips
for use, care and maintenance of the
unit.

Throughout this manual and on the product itself, you will find safety
alerts and helpful, informational messages preceded by symbols or key
words.  The following is an explanation of those symbols and key
words and what they mean to you.

S

AFETY

MANUAL

 

SAFETY

 

SYMBOLS

 

AND

 

IMPORTANT

 

INFORMATION

This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.

The circle with the slash symbol means whatever is shown
within the circle is prohibited.

Содержание srm-251





























Отзывы: