12
1.
OPERATOR'S MANUAL
- Included in plastic bag (co-pack). Read before operation and keep in a safe place for
future reference, i.e., operation, maintenance, storage and specifications.
2.
SAFETY MANUAL
- Included in plastic bag (co-pack). Read before operation and keep in a safe place for future
reference to learn proper, safe operating techniques.
3.
POWER HEAD
- Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.
4.
GRIP
- Rear (right hand) handle.
5.
STOP SWITCH
- "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to
RUN, BACK to STOP.
6.
FRONT HANDLE
- The front (loop) handle is not assembled to the Drive Shaft assembly (some models) and must be
positioned for proper cutting attitude and operator comfort.
7.
DRIVE SHAFT ASSEMBLY
- Includes the Rear (right hand) Handle assembly, Gear Housing assembly, front (loop,
left hand) Handle assembly, Flexible Drive Cable and Safety Decal.
8.
NYLON CUTTING ATTACHMENT
- Contains replaceable nylon trimming line that advances when the trimmer head
is tapped against the ground while the head is turning at normal operating speed.
9.
CUT-OFF KNIFE
- Automatically trims line to the correct length: 5" after head is tapped on the ground. If trimmer is
operated without a cut-off knife the line will become too long, the engine will overheat and engine damage may occur.
10.
PLASTIC DEBRIS SHIELD ASSEMBLY
- Included in plastic bag (co-pack).
MUST
be installed on unit before use,
see Assembly Instructions. Shield assembly includes the Cut-Off Knife and Safety Decal. Mounts on the Gear
Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced
during the trimming operation. This shield must be replaced with the steel shield for blade use.
11.
THROTTLE TRIGGER
- Spring loaded to return to idle when released. During acceleration, press trigger gradually
for best operating technique.
12.
ARM REST
- Provides arm rest during operation and protects arm from the hot engine.
13.
SPARK PLUG
- Provides spark to ignite fuel mixture.
14.
MUFFLER/SPARK ARRESTOR
- The muffler controls the exhaust noise while the spark arrestor prevents hot,
glowing particles of carbon from leaving the muffler where they could possibly start a fire. Built in accordance with
SAEJ335, this product is approved for use on U.S. Forest Land and within the states of California, Maine, Oregon and
Washington if the spark arresting screen is in place and in good repair.
15.
FUEL TANK
- Contains fuel and fuel filter.
16.
RECOIL STARTER HANDLE
- Pull recoil handle slowly until starter engages, then quickly and firmly. When engine
starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
17.
FUEL TANK CAP
- Covers and seals fuel tank opening.
18.
PRIMER BULB
- Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-
tor for starting. Pump the bulb 10 times until fuel is visible in clear fuel return line.
19.
AIR CLEANER
- Contains replaceable filter element.
20.
CHOKE
- The choke control lever is located on the top of the air filter case. Pull choke knob up to close the choke
for cold starting. Push knob down for the "RUN" position.
21.
SHOULDER HARNESS
- An adjustable strap that suspends the unit from the operator. Using the strap reduces
operator fatigue.
22.
METAL BLADE SHIELD
- Required when unit is equipped with blades. Do not operate unit without shield.
23.
BLADE
- Circular blade for grass, weed or brush cutting applications. Harness, metal shield and U-handles required
for blade operation.
24.
U-HANDLE
- Required for metal blade operation.
25.
SAFETY VIDEO
- (Not included with unit) P/N 99922202540 English version only is available at a cost of $5.00 from
ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating tech-
niques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information
on safe operation.
