manualshive.com logo in svg

Echo SRM-2320T, Руководство оператора

Поделиться
Скачать
Echo SRM-2320T Скачать руководство пользователя страница 33

SRM-2320T

MAINTENANCE

X7732278300

33

© 08/2019 ECHO Inc.

Air Filter

Level 1.

1.

Close choke (COLD START [

] position). This prevents dirt from 

entering the carburetor throat when the air filter is removed. Brush 
accumulated dirt from air cleaner area.

2.

Remove air filter cover. Brush 
dirt from inside cover.

3.

Replace filter if it is damaged, 
fuel soaked, very dirty, or the 
rubber sealing edges are 
deformed.

• Lightly brush debris from 

filter.

• Soak heavily soiled filters in 

water/detergent solution to 
loosen dirt, then brush 
lightly. 

• Rinse with clean water and 

allow to dry completely before reuse. 

4.

Install air filter in air filter case. 

5.

Install air filter cover.

Fuel Filter

Level 1.

Fuel is VERY flammable. Use extreme care when mixing, storing 
or handling, or serious personal injury may result.

Parts Required: Tune-Up Kit

Parts Required:

TUNE UP KIT.

Содержание SRM-2320T





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды